Bedienungsanleitung Sharp ARM237 (Seite 222 von 263) (Englisch)

26408

222

Zoom out

Zoom in

Vorherige Seite

1/263

Nächste Seite

104

KEY OPERATOR PROGRAMS

● F-code confidential box (print passcode)

A print passcode must be programmed to permit

printing of faxes received in the F-code confidential

box.

Touch [CONFIDENTIAL] and program a

box name and sub-address/passcode as

explained in step 1 of "Programming an

F-code memory box" (p.103).

Touch the [PRINT PIN] key.

Use the numeric keys to enter a 4-digit

number.

• If you make a mistake, press the [CLEAR] key ( )

and then enter the correct number.

• To cancel before completing entry of the number,

touch the [CANCEL] key. You will return to the screen

of step 2.

Touch the [OK] key.

You will return to the programming screen for F-code

confidential boxes. The entered print passcode will

appear, and "REGISTRATION IS COMPLETED." will

appear next to the box number.

Touch the [NEXT] key or the [EXIT] key.

• To program another memory box, touch the [NEXT]

key.

• To exit, touch the [EXIT] key.

● F-code relay broadcast memory box (end

receiving machines)

Store the end receiving machines for a relay

broadcast transmission when your machine is the

relay machine and receives a fax in its F-code relay

broadcast memory box.

Touch [RELAY BROADCAST] and

program a box name and

sub-address/passcode as explained in

step 1 of "Programming an F-code

memory box" (p.103).

Touch the [RECIPIENT] key.

The address selection screen appears.

Select indexes as needed and touch rapid

keys to select the end receiving machines.

If needed, touch the or key to move

through screens.

• The selected rapid keys are highlighted and stored as end

receiving machines.

• If you touch an incorrect rapid key, touch it again so that it

is not highlighted.

• You can also touch the [10-KEY PAD] key to enter full fax

numbers with the numeric keys.

To check the stored end receiving machines,

touch the [ADDRESS REVIEW] key.

A list of the selected destinations appears.

If you need to delete a destination from the list, touch it and

then touch the [YES] key in the message that appears.

Touch the outer [OK] key.

You will return to the programming screen for F-code relay

broadcast memory boxes. The number of stored end

receiving machines will appear, and "REGISTRATION IS

COMPLETED." will appear next to the box number.

Touch the [NEXT] key or the [EXIT] key.

•

To program another memory box, touch the [NEXT] key.

• To exit, touch the [EXIT] key.

• Enter a 4-digit number for the print

passcode. The characters " " and "#"

cannot be used.

• The print passcode cannot be omitted.

Take care not to forget the

programmed print passcode. In the

event that you forget it, print out the

confidential ID list. ("LIST PRINT"

(p.105))

Note

Caution

• A total of 120 end receiving machines can

be stored in up to 10 groups. If you attempt

to store more that this, a message will

appear and storing will not be possible.

• Speed dial numbers and rapid numbers

that include a sub-address cannot be

stored.

• The same number cannot be stored twice

in a group.

Note

F-CODE MEMORY BOX / RELAY BROADCAST

SELECT ADDRESS.

FREQUENT USE ABCD EFGHI JKLMN OPQRST UVWXYZ

ABC GROUP

TOKYO

S.F.

10-KEY PAD

ADDRESS REVIEW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp ARM237 Seite 222

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info