21204

Sharp DVHR300u Seite 108

108
Zoom out
Zoom in
Vorherige Seite
1/126
Nächste Seite
108
Troubleshooting
The Recorder power does not turn on.
The Recorder sounds like it is operating, even when power is
turned off.
The disc is automatically ejected after closing the disc tray.
No picture.
The Recorder does not play a disc.
Settings have disappeared.
Screen freezes and operation buttons do not work.
The remote control does not work.
No sound or sound is distorted.
The picture from external input is distorted.
The screen is stretched vertically or
horizontally.
A disc recorded using this Recorder cannot be played back
on another DVD player.
•
Is the power cord firmly plugged into the AC outlet?
•
If the power cord is plugged into the outlet, unplug it once, wait about one minute, and then plug it in again.
Then turn power on.
•
This is the sound the Recorder makes during operation like timer recording.
•
Make sure that the disc is loaded properly (aligned in disc tray and label-side up).
•
Take out the disc and clean it.
•
Make sure that region number on the disc match the region number in this Recorder.
•
Make sure that the disc is playable.
•
Make sure that the cables are connected correctly.
•
Make sure that the connected TV or the AV amplifier is set to the correct input.
•
Take out the disc and clean it.
•
Make sure that region number on the disc match the region number in this Recorder.
•
If you set to “PROGRESSIVE SCAN ON”, non-broadcast video signals will not be output from terminals other
than COMPONENT Output jacks.(Page 102)
•
Take out the disc and clean it.
•
Make sure that the disc is loaded properly (aligned in disc tray and label-side up).
•
Make sure that region number on the disc match the region number in this Recorder.
•
Remove the dew in the Recorder.
•
Check that the disc is recorded in NTSC format.
•
The Recorder cannot playback video which was not recorded normally.
•
Proper playback may be impossible due to the state of the disc recording, a scratched, warped or dirty disc, the
state of the pick-up, or compatibility issues between this Recorder and the disc being used.
•
If, while its power is on, the Recorder is unplugged (or there is a power failure) for more than about 1 hour, the
settings will be lost. Make sure that you turn off the Recorder before unplugging the power cord.
•
Press
■STOP/LIVE
and restart playback.
•
Turn off the power and turn on the power again.
•
If power does not go off, press the
RESET
button inside the front door of the Recorder.(Page 110)
•
Is the Tamper Proof function active?(Page 38)
•
Set the remote control and the Recorder to the same remote control code.(Page 21)
•
Use the remote control within its operating range.
•
Replace the batteries.
•
If the volume of TV or amplifier is set to minimum, turn the volume up.
•
There is no sound during still mode, slow motion playback, fast forward and fast reverse.
•
DVD audio recorded in DTS is only output from the DIGITAL AUDIO Output terminals. Connect a DTS-
compatible digital amplifier or decoder to the DIGITAL AUDIO Output OPTICAL or COAXIAL terminal on this
Recorder.
•
Check that the audio cable is connected correctly.
•
Check that the cable plugs are clean.
•
Take out the disc and clean it.
•
Audio may not be output depending on the audio recording status, such as when audio other than an audio
signal or non-standard audio is recorded for the audio content of the disc.
•
If the signal is copy-protected, you cannot connect via this Recorder. Connect the external equipment directly
to your TV.
•
Set the TV mode according to the TV you are connecting.(Page 102)
•
If the above operation does not set the TV mode, set it using the functions of the connected TV.
•
Check that the disc is finalized when the disc is in video mode.
•
Some players will not play even a finalized disc.
•
If the disc was recorded in VR mode, it can only be played back with an RW compatible player. (In some
cases, the disc must be finalized.)
The following problems do not always suggest a defect or malfunction of this Recorder.
Perform the checks listed below before calling service.
Problem Suggested Solution
… 108 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sharp DVHR300u wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info