Bedienungsanleitung Sharp ER-A280F (Seite 174 von 188) (Englisch)

564782

174

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

172

Setting the date and time when the automatic EURO modification operation should be executed

To certainly execute the automatic modification operation, you can program the scheduled date and time to

execute the automatic EURO modification operation. From ten days before the preset date, the remaining

days are printed at the bottom of the daily full resetting report.

Date and time setting will be reset after the execution of automatic modification operation, and again you

can program the date and time for the next automatic modification operation.

Also you can make the automatic EURO modification operation compulsory. When the above-mentioned

preset date and time has come, and also when you start an entry in the REG/MGR mode, the error

message “EURO CHANGE ENTRY COMPULSORY” will be displayed. You cannot start any operation in

the REG/MGR mode until you make the operation.

Automatic EURO modification operation

1. Select the X2/Z2 mode.

2. Select “8 EURO STATUS” from the menu.

3. Select the status you want to set (B, C or D) referring to the table on the previous page. Press the

key to toggle the options.

Please note that once you set a status, you cannot return to the previous status(es).

Important note

As for the miscellaneous keys, such as

and

)

keys, and for the HALO setting, the automatic

conversion will not be made. You need to change the % rates or amounts in the PGM1/PGM2 mode

after the execution of the automatic modification operation for EURO so that they are based on

amounts in EURO.

It is executed some of following operation which is needed for each status.

(1) Issue general Z1 report. (2) Issue general Z2 report. (3) Clear GT1/GT2/GT3. (4) Change

PGM function “Total and change amount printing — With foreign/Domestic only”. (5) Change

PGM function “Exchange1 amount printing for total validation print — YES/NO” and “Total

validation print amount printing — With foreign/Domestic only”. (6) Change PGM function

“Exchange1 calculation method — Division/Multiplication”. (9) Change PGM function

“Converting the preset unit prices of departments/PLUs/EANs to the ones in EURO currency -

YES/NO. (10) Set “Exchange1 currency descriptor” as the suitable data. (11) Set “Exchange1

TAB” as the suitable data.

This job cannot set the following additional EURO function. You must set the following items by

each programming after executing the automatic EURO modification operation.

(1) Exchange1 rate, (2) “Check, Credit operation for Exchange1 — YES/NO”

(3) Foreign currency drawer number (if installed)

Also when you are using any of the

through

keys, you must change these rates.

NOTE

ER-A280F_N(SEEG)(E)-9 09.6.18 6:56 AM Page 172

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp ER-A280F Seite 174

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp ER-A280F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info