Bedienungsanleitung Sharp FU-S63E (Seite 21 von 92) (Deutsch, Englisch, Holländisch, Französisch)

459674

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

FRANÇAIS

NEDERLANDS

DEUTSCH

E-19

TROUBLESHOOTING

Before calling for repair, please review the list below, since the problem may not be a unit malfunction.

SYMPTOM

REMEDY (not a malfunction)

The Remote Control does not

work.

• Have the batteries been depleted?

• Are the batteries inserted correctly?

• Is a fluorescent lighting in the room flickering due to service

life?

Odours and smoke are not

removed.

• Clean or replace the filters if they appear to be heavily soiled.

(Refer to E-16,E-18)

The CLEAN-SIGN Light lights

green even when the air is

impure.

• The air could be impure at the time the unit was plugged in.

(Refer to E-12)

Pull out the plug from the electrical outlet, and insert the plug

one minute later.

The CLEAN-SIGN Light lights

orange or red even when the air

is clean.

• The sensitivity of the sensors become unstable when the

opening of the odour sensor or dust sensor is dirty or is clogged.

Clean the dust around the sensor opening using a vacuum

cleaner. (Refer to E-17)

• When in Clean Mode, the Plasmacluster Indicator Light colour

will not change.

A clicking or ticking sound is

heard from the unit.

• Clicking sound or ticking sound is emitted when the unit is

generating ions.

The discharged air has an

aroma or odour.

• Check to see if the filters are heavily soiled.

Replace the filters.

• Plasmacluster Air Purifiers emit small traces of ozone which

may produce an odour. These ozone emissions are well below

safety levels.

The Plasmacluster Indicator

Light remains blue and does

not change.

The unit does not operate when

cigarette smoke is in the air.

• Is the unit installed in a location that is difficult for the sensor to

detect cigarette smoke?

• Are the dust or odour sensor openings blocked or clogged?

(In this case, clean the openings.) (Refer to E-17)

The MIST Unit Indicator Light

remains activated even after

replacing filter.

• After replacing filters, connect the power cord to an outlet and

press the Mist Unit Reset Button. (Refer to E-15)

The Plasmacluster Indicator

Light or the CLEAN-SIGN Light

will not activate.

• Check to see if the Lights OFF Mode on the Remote Control is

selected. If so, then press the Lights ON/OFF Button on the

Remote Control to activate the indicator lights.

(Refer to E-11)

(Care Cycle : MIST Filter : 1 month)

Plasmacluster Indicator Light

repeat colour cycles between

blue and green.

Mist Unit Indicator Light does not

turn on even water is in.

When the water of the tank does

not decrease or the decrease of

the water is slow.

• The ION SHOWER operation is working.

• Check to see if the Mist Unit and Tank are installed correctly.

• Check the Mist Filter. Replace the filter when it is heavily soiled.

(Refer to E-14,18)

• Please check if the impurities adhered to the surface of the

Float.

Clean the Mist Tray.

Check to see check if the Main Unit is put on a inclined surface.

The CLEAN-SIGN LIGHT switches

frequently.

• The CLEAN-SIGN Light will automatically switches the colours

when detected by dust and odour sensors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp FU-S63E Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp FU-S63E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info