Bedienungsanleitung Sharp K-90D10BM2 (Seite 19 von 25) (Englisch)

786984

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

EN - 19

5. CLEANING AND

MAINTENANCE

5.1 CleaninG

WARNING: Switch off the appliance

and allow it to cool before cleaning is

to be carried out.

General Instructions

• Check whether the cleaning materials

are appropriate and recommended by

the manufacturer before use on your

appliance.

• Use cream cleaners or liquid cleaners

which do not contain particles. Do not

use caustic (corrosive) creams, abrasive

cleaning powders, rough wire wool or

hard tools as they may damage the

cooker surfaces.

Do not use cleaners that contain

particles as they may scratch the

glass, enamelled and/or painted parts

of your appliance.

• Should any liquids overflow, clean them

immediately to avoid parts becoming

damaged.

Do not use steam cleaners for

cleaning any part of the appliance.

Cleaning the Inside of the Oven

• The inside of enamelled ovens are best

cleaned while the oven is warm.

• Wipe the oven with a soft cloth soaked

in soapy water after each use. Then,

wipe the oven over again with a wet

cloth and dry it.

• You may need to use a liquid cleaning

material occasionally to completely

clean the oven.

Catalytic Cleaning

Catalytic liners are installed within the oven

cavity. These are the matte-finished, light-

coloured panels on the sides and/or the

matte-finished panel at the rear of the oven.

They work by collecting any grease and oil

residue during cooking.

The liner self-cleans by absorbing fats and

oils and burning them to ash, which can

then be easily removed from the floor of

the oven with a damp cloth. The lining must

be porous to be effective. The liner may

discolour with age.

If a large amount of fat is spilled onto

the liner it may reduce its efficiency. To

overcome this problem, set the oven to

maximum temperature for about 20 - 30

minutes. After the oven has cooled, wipe

out the floor of the oven.

Manual cleaning of the catalytic liners is not

recommended. Damage will occur if a soap-

impregnated steel wool pad or any other

abrasives are used. In addition, we do not

recommend the use of aerosol cleaners on

the liners. The walls of a catalytic liner may

become ineffective due to excess grease.

The excess grease can be removed with

a soft cloth or sponge soaked in hot water,

and the cleaning cycle can be carried out

as described above.

Removal of the Catalytic Liner

To remove the catalytic liner, remove the

screws holding each catalytic panel to the

oven.

Cleaning the Glass Parts

• Clean the glass parts of your appliance

on a regular basis.

• Use a glass cleaner to clean the inside

and outside of the glass parts. Then,

rinse and dry them thoroughly with a dry

cloth.

Cleaning the Stainless Steel Parts (if

available)

• Clean the stainless steel parts of your

appliance on a regular basis.

• Wipe the stainless steel parts with a soft

cloth soaked in only water. Then, dry

them thoroughly with a dry cloth.

Do not clean the stainless steel parts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp K-90D10BM2 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info