Bedienungsanleitung Sharp KD-NCB0S7PW9 (Seite 13 von 94) (Englisch)

787156

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

EN - 9

2. INSTALLATION

• Before contacting the local Authorised

Service Provider for the installation

of the dryer, check the information in

the user manual to make sure that the

electrical installation and water outlet is



electrician and a plumber to have the

necessary adjustments made.

• It is the customer’s responsibility to

prepare the dryer’s installation place, as

well as the electricity and waste water

installation. Before installation, check

the dryer for damage. If damaged, do

not have it installed. Damaged products

may endanger your health.

• 

surface.

• Run the dryer in a dust-free

environment where the air ventilation

is good.

• The clearance between the dryer and

should not be reduced with

objects such as carpets, wood or tape.

• Do not block the ventilation grills

found on the plinth of the tumble dryer.

• The appliance must not be installed

behind a lockable door, a sliding door

or a door with a hinge on the opposite

side of the tumble dryer, in such a

way that blocks the full opening of the

tumble dryer door.

• Once the dryer has been installed, the

connections must remain stable. When

installing the dryer, make sure that the

rear surface is not leaning on anything

(e.g. tap, socket).

• The operating temperature of the dryer

is +5°C to +35°C. If operated out of this

temperature range, the performance of

󰀨

the product will be damaged.

• Be careful when carrying the product

since it is heavy. Always wear safety

gloves.

• Always install the product should be

placed against a wall.

• The rear surface of the product should

be placed against the wall.

• When the product is placed on a stable

surface, use a water level to check if it

is fully stable. If not, adjust the feet until

it becomes steady. Repeat this process

every time you relocate the product.

• Do not place the dryer onto the power

cable.

2.1. Connection to Water Outlet (with

optional drain hose)

In products with a condenser unit, water

accumulates in the water tank during

the drying process. You must empty the

accumulated water after each drying

process. Instead of periodically emptying

the water tank, you can also use the water

drain hose provided with the product to

directly drain the water outside.

2.1.1. Connecting the Water Discharge

Hose

1. Pull and take out the end of the hose at the

back of the dryer. Do not use any tools to

take out the hose.

2. 





3. 

.

ATTENTION: The hose must be

connected in a manner that it cannot be

displaced. If the hose comes out during



your house.

IMPORTANT: The water discharge

house must be installed at a height of 80

cm maximum.

IMPORTANT: The water discharge

hose must not be bent between the outlet

and the product, folded or stepped over.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp KD-NCB0S7PW9 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp KD-NCB0S7PW9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info