Bedienungsanleitung Sharp LC-20S4U-S Operation Manual (Seite 15 von 43) (Englisch)

13289

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

Press POWER, located on the upper side of the main

unit, to turn on the TV. The SELECT LANGUAGE

screen will be displayed.

Press '/" to select “ENGLISH”, “ESPAÑOL”

(Spanish) or “FRANÇAIS” (French).

ENGLISH

ESPAÑ OL

FRANÇ AIS

Press ENTER to access CH-SETTING mode.

Press '/" to select “ON” or “OFF”. When you select

“ON”, the LCD TV set will automatically memorize the

broadcasting channels.

OFF

• If you select “OFF”, EZ SETUP will be canceled.

Press ENTER to access AUTO CLOCK mode.

Press '/" to select “ON” or “OFF”.

When you select “ON”, the LCD TV set will

automatically adjust the clock to search time-signals

(EDS signals), which are provided by some TV stations.

The AUTO CLOCK setting may take from several

minutes to an hour depending on the number of

channels to receive and signal status. If you know the

channel of the EDS signal carrier (PBS or other) in your

area, select “OFF” and follow the procedure in AUTO

CLOCK Setting. (See page 15.)

OFF

■ When you turn on the TV for the first time, it will automati-

cally memorize the broadcasting channels and clock.

Please perform the following instructions before you press

POWER.

(1)

Insert the batteries into the remote control. (See page 8.)

(2)

Connect the antenna cable to the LCD TV set. (See page 9.)

(3) Connect the AC adapter to the POWER INPUT terminal

of the LCD TV set and plug in the AC cord to the wall

outlet. (See page 10.)

EZ SETUP (With AUTO CLOCK Setting)

EZ SETUP during the First Power On

POWER

Press ENTER to access START EZ SETUP mode.

Press '/" to select “YES”, and press ENTER.

• If you want to stop the EZ SETUP process once it has

started, press MENU and it will be canceled. If you want to

set up again, please refer to page 24 on CH-SETTING.

YES

CONNECT ANTENNA

OR CABLE.

The tuner will automatically search for the broadcasting

and cable TV channels. (The channel number will

automatically increase when it appears.)

PLEASE WAIT

AUTO PROGRAMMING

The LCD TV set will automatically switch to searching

for EDS signals.

If EDS signals are received, the channel number and time will

be displayed, and then the screen shown in step 5 appears.

PLEASE WAIT

NOW SEARCHING TIME

Once EZ SETUP is completed, the lowest channel

number memorized will be displayed.

STEREO

SAP

MONO 11:53AM

• Do not let the EZ SETUP screen remain unattended for a long time.

• If EZ SETUP does not memorize all the channels in your region,

please refer to page 24 for more information on manually memo-

rizing the channels using CH-SETTING.

• It may be difficult to preset when the broadcasting signals are

weak, the channel cycle frequency is incorrect or the frequency

jamming is occurring around the area. Please refer to page 24 for

more information on manually memorizing channels using

CH-SETTING.

• If there are no channels with EDS signals or the antenna signal is

weak, the AUTO CLOCK setting may not operate. In this case, a

“EDS CH IS NOT AVAILABLE.” message will appear and the

mode will change to MANUAL CLOCK setting. Refer to page 16 to

set the clock manually.

LC-20S4U_E_P14-20.p65 04.12.14, 1:14 PM14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp LC-20S4U-S Operation Manual Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info