Bedienungsanleitung Sharp LC-32LE362EN (Seite 23 von 35) (Englisch)

567410

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

English - 22 -

4. Check if you have entered the correct frequency. if

you have done manual tuning.

5. Please retune the channels.

6. The picture quality may degrade when two devices

are connected to the TV at the same time. In such a

case, disconnect one of the devices.

No picture

1. No Picture means that your TV is not receiving a

transmission. Have you selected the correct button on

the remote control? Try once more. Also make sure

the correct input source has been selected.

2. Is the aerial connected properly?

3. Are the plugs connected tightly to the aerial socket?

4. Is the aerial cable damaged?

5. Are suitable plugs used to connect the aerial?

6. If you are in doubt, consult your dealer.

Strange, light, dark colour or colour misalignment

• Adjust the picture settings. Press the MENU button

and select Picture. Press OK to open the Picture

Settings menu.

• Is the room too bright? The picture may look dark in

a room that is too bright.

No sound

1. Has the TV been set to mute? To cancel mute,

press the “ ” button, or increase the volume level.

2. Sound is coming from only one speaker. Is the

balance set to one extreme? See Sound Menu

section.

Remote control - does not operate

Your TV no longer responds to the remote control. The

batteries may be exhausted, if so you can still use the

control buttons on the TV. (* Is only possible if they

are not blocked by parental control.)

Power is suddenly turned off

• The TV’s internal temperature has increased.

Remove any objects blocking the vent or clean.

• Is a sleep timer set? Press the MENU button and

select Settings. Select Timers in the sub-menu

and press OK. Press Left or Right button to set the

Sleep Timer as Off.

• Is Auto TV OFF function is activated? Press the

MENU button and select Settings. Than select Other

Settings and press OK. In the sub-menu highlight

Auto TV OFF and press Left or Right button to set

as Off.

Input sources - can not be selected

1. If you cannot select an input source, it is possible

that no device is connected.

2. Check the AV cables and connections if you have

tried to connect a device.

Recording Unavailable

To record a programme, you should rst connect

a USB disk to your TV while the TV is switched

off. You should then switch on the TV to enable

recording feature. Otherwise, recording feature will

not be available. If you cannot perform recording, try

switching off the TV and then re-inserting the USB

device while the TV is switched off.

USB Is too Slow

If “USB disk writing speed too slow to record”

message is displayed on the screen while starting a

recording, try restarting the recording. If you still get

the same error, it is possible that your USB disk does

not meet the speed requirements. Try connecting

another USB disk.

Internet Connection Not Available / DLNA Mode

Not Operating

Check if the ethernet cable is connected properly.

Check if the Network settings are correct.

If the MAC address (a unique identier number) of

your PC or modem has been permanently registered,

it is possible that your TV might not connect to

the internet. In such a case, the MAC address is

authenticated each time when you connect to the

internet. This is a precaution against unauthorized

access. Since your TV has its own MAC address,

your internet service provider cannot validate the MAC

address of your TV. For this reason, your TV cannot

connect to the internet. Contact your internet service

provider and request information on how to connect

a different device, such as your TV, to the internet.

It is also possible that the connection may not be

available due to a firewall problem. If you think

this causes your problem, contact your internet

service provider. A rewall might be the reason of a

connectivity and discovery problem while using the TV

in DLNA mode or while browsing via DLNA.

Invalid Domain

Ensure that you have already logged on to your PC

with an authorized username/password and also

ensure that your domain is active, prior to sharing

any les in your DLNA server program on your PC. If

the domain is invalid, this might cause problems while

browsing les in DLNA mode.

The TV sometimes makes a cracking sound.

This is not a malfunction. This happens when the

cabinet slightly expands or contracts according to the

changes in the ambient temperature. This does not

affect the TV’s performance.

Miracast image/audio cannot be output to

the TV.

Check if the pairing is made properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp LC-32LE362EN Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp LC-32LE362EN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info