Bedienungsanleitung Sharp LC-40LE540E (Seite 11 von 44) (Englisch)

475589

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Initial auto installation

When the TV is powered on for the first time after purchase,

the initial auto installation wizard appears. Follow the menus

and make the necessary settings one after another.

1 Press a on the TV.

• The initial auto installation wizard appears.

2 Setting the OSD language.

Press

a/b/c/d to select the desired language.

3 Setting the country.

Press ▲/▼/◄/► to select your country or area.

• This setting screen only appears during the initial auto

installation.

4 Select time zone.

5 Select broadcast settings.

Press ▲/▼ to select “Tuner type”. Press ◄/► to

select between differents tune type:

CADTV: Cable digital broadcasts.

ATV: Analogue broadcasts.

DTV: Digital broadcasts.

DTV + ATV: Digital and analogue broadcasts.

CADTV+ATV: Cable and analogue broadcasts.

SADTV: Satellite broadcasts.

SADTV + ATV: Satellite and analogue broadcasts.

6 Selecting the TV location.

Press ◄/► to select where you will use this TV, and

then press OK.

•HOME: For domestic use.

•STORE: DYNAMIC mode is predetermined. If the

Picture Mode is changed, the TV will automatically

switch back to DYNAMIC when there is no signal input

from the TV or remote control unit for 30 minutes.

Quick guide

If you have chosen STORE by mistake, go to Settings

→ Restore Factory Default → OK, and the TV returns

to the initial screen.

7 Starting channel search.

Press ▼ to select Next and then press OK.

• If you want to search for more broadcasts, execute

“DTV (or ATV, or CADTV) manual tuning” from the

menu “CHANNEL” (Page 22).

• To watch both analogue broadcasts and digital

broadcasts, you should perform the channel search

setting “DTV+ATV” or “CADTV+ATV”.

• Is not possible to search digital and cable digital

broadcasts at the same time.

8 The TV searches for, sorts and stores all the

receivable TV stations according to their settings

and the connected antenna.

• To cancel the initial auto installation in progress, press

END.

NOTE

• If you turn the power on the TV after performing step 4,

initial auto installation wizard does not appear. The auto

installation function allows you to execute the installation

again from the Channel menu (Page 22).

• When "France" is selected in the Country setting, the PIN

code setting cannot be skipped.

• After initial Auto Tuning is completed, the default PIN is

automatically set to “3001”. To change the PIN setting, refer

to Lock menu on page 21.

If you install a DVB-T/T2/S/S2 antenna for the first time

of relocate it, you should adjust the alignment of the

antenna to receive a good reception while checking the

antenna setup screen.

1 Press a channel you want to check.

2 Press MENU.

3 Press ► to select “Channel” menu and then press

OK.

4 Press ▲/▼ to select "Signal Information" and

then press OK.

5 Position and align the antenna so that the maximum

possible values for “Signal Strength” and “Signal

Quality” are obtained.

NOTE

• The values of “Signal Strength” and “Signal Quality” indicate

when to check the appropriate alignment of the antenna.

Checking quality and

signal strength

Confirm the following before turning

on the power

E Is the antenna cable connected?

E Is the AC cord plugged in?

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp LC-40LE540E Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp LC-40LE540E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info