65009
27
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
TV menu
Source Labels
You can assign a label to each input source as you
prefer in the label list�
Go to
1. Installation > Source labels
Assign a input source and press > to select a
2.
label from label list.
Press
3. b on the remote control and check the
result.
Assign a channel decoder (For ATV)
Decoders that decode channels can be connected to
SCART� You have to assign the TV channel as a channel
to be decoded� Then assign the connection where the
decoder is connected�
Press MENU on the remote control and select
1.
Installation > Decoder.
Installation Decoder
2 ...
3 ...
1 ...
Country
Channel installation
Source labels
Decoder
Current software info
AV reset
Factory reset
Language
TV Menu
Press 2. to enter the list.
Press
3. < or > to select the channel to decode.
Press
4. OK to select or unselect the channel.
Press
5. to return to the previous menu.
Press
6. MENU to exit.
Check your current software version
Press MENU on the remote control and select
Installation > Current software info.
Update software (digital broadcasts)
If using (DVB-T) digital broadcasts, your TV automatically
receives software updates� If you receive a message
on-screen prompting you to update your software:
Select • Accept (recommended) to update the
software immediately.
Select • Reject to exit the update (not
recommended).
Select • Remind me later to be reminded to update
the software later.
NOTE
To scan all carriers for upgrade availability, perform the manual •
upgrade�
The software upgrade may take about 30 minutes, but may •
take longer (up to 1 hour) depending on the signal status�
CAUTION
Do not disconnect the AC cord when the software
upgrade is in progress, as this may cause the upgrade
to fail. If problem arises ask a qualified service
personnel before the software upgrade period expires.
AV reset
To reset the Audio and Video to default settings�
Press MENU on the remote control and select
1.
Installation > AV reset
Press
2. to select “Start now” and press OK.
Press
3. MENU to exit.
Factory reset
When you activate the Factory reset , the TV needs to
be reset from First time installation�
Press MENU on the remote control and select
1.
Installation > Factory reset
Press
2. to select “Start now” and press OK.
Press
3. MENU to exit.
25
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sharp LC-42SB55 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sharp LC-42SB55

Sharp LC-42SB55 Bedienungsanleitung - Holländisch - 32 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info