Bedienungsanleitung Sharp LC-60LE830E (Seite 60 von 85) (Englisch)

475409

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

PC control of the TV

• When a programme is set, the TV can be controlled

from the PC using RS-232C or IP. The input signal (PC/

video) can be selected, the volume can be adjusted and

various other adjustments and settings can be made,

enabling automatic programmed playing.

• Use an RS-232C serial control cable (cross type),

ETHERNET cable (commercially available) or wireless

LAN USB adapter for the connections.

NOTE

• This operation system should be used by a person who

is accustomed to using PCs.

Communication conditions for IP

LAN

ETHERNET cable (commercially available)

Connect to the TV with the following settings made

for IP on the PC.

IP protocol

TCP/IP

Host IP address

Set the IP address on the TV

Service

None (Do not select Telnet

or SSH)

TCP port#

Set a port number on the TV

menu (Control port)

When you set your ID and password on the TV

menu, you need to enter them as soon as you

connect to the TV.

NOTE

• The connection will be cut off when there has been no

communication for 3 minutes.

View setting

IP Control setup

1 Go to “Menu” > “Setup” > “View setting” >

“Network setup” > “IP Control setup” > select

“Change”.

2 To use IP Control, select “Enable”.

3 Set the device name.

4 Set your login ID and password.

5 Set the port to use with IP Control.

6 Confirm the settings, and then press “OK”.

Communication conditions for RS-232C

RS-232C serial control cable (cross type)

(commercially available)

Set the RS-232C communications settings on the

PC to match the TV’s communications conditions.

The TV’s communications settings are as follows:

Baud rate

9,600 bps

Data length

8 bits

Parity bit

None

Stop bit

1 bit

Flow control

None

Communication procedure

Send the control commands from the PC via the

RS-232C connector.

The TV operates according to the received

command and sends a response message to the

PC.

Do not send multiple commands at the same time.

Wait until the PC receives the OK response before

sending the next command.

Make sure to send “A” with the carriage return and

confirm that “ERR” returns before operating.

Command format

Eight ASCII codes +CR

nop

C1 C2 C3 C4 P1 P2 P3 P4



Command four digits: Command. The text of

four characters.



Parameter four digits: Parameter 0_9, blank, ?,

minus



Return code (0DH): ?

Parameter

Input the parameter values, aligning left, and fill with

blank(s) for the remainder (be sure that four values

are input for the parameter).

When the input parameter is not within an adjustable

range, “ERR” returns (refer to “Response code

format”).

0055

100

0009

When “?” is input for some commands, the present

setting value responds.

????

Response code format

Normal response Problem response

(communication error or

incorrect command)

ERR

Return code (0DH) Return code (0DH)

Connecting a PC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp LC-60LE830E Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp LC-60LE830E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info