Bedienungsanleitung Sharp LC-80LE857E (Seite 14 von 94) (Englisch)

525758

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Inserting the CA card into the CI

module

NOTE

• It takes a few minutes to certify the licence key when

you insert a CA card into the CI+ compatible CI module

for the first time. This process may fail when there is no

antenna input or you have never run “Auto installation”.

• The CI+ compatible CI module sometimes upgrades its

firmware. You may not receive any TV images before

upgrading. You can only use the power button during

upgrading.

• Copy protected content may not be output or may be

output with a copy control signal. The protect icon* is

displayed when P.INFO is pressed while watching copy

protected contents.

* Protect icon: X

• If the TV displays an update confirmation message for

the CA card while receiving CI+ compatible broadcasts,

follow the screen prompts.

• Make sure that the CI module is properly inserted.

• If the old CAM is used, authentication may fail. In such

cases, contact the contracted service provider.

Recording CAM PIN setting

When a CAM PIN code is required for recording a

programme, it is necessary to enter the CAM PIN

code in advance.

1 Go to “TV Menu” > “Setup” > “Option” >

“CI setting” > “Recording CAM PIN setting”.

2 Enter the CAM PIN code.

NOTE

• If a PIN code is not entered or is entered incorrectly, the

programme will not be able to be recorded/played back.

CI plus 1.3 Standard

CI Plus is an advanced development of the DVB

Common Interface Standard.

1 Regarding security

There are some regulations in recording functions.

The playback of encrypted programmes is

strongly dependent on which CA module is

used. The playback of encrypted recordings may

sometimes not be possible, or only during limited

time. Programme providers, who use the CI Plus

standard, can assign different rights for their

broadcast programmes.

Exercise caution when using USB-recording to

record broadcast programmes (Pages 51–54).

2 Operator service list management (Operator

profile)

Under the 1.3 specification the CAM may provide

the channel listing parameters (channel number,

frequency etc.) and these can be updated while in

use.

Refer to “Operator profile” on page 21.

In order to receive coded digital stations, a common

interface module (CI module) and a CA card must be

inserted in the CI slot of the TV.

1 Carefully insert the CI module in the CI slot with

the contact side forward.

2 The logo on the CI module must be facing

outward from the rear of the TV.

Checking CI module information

Go to “TV Menu” > “Setup” > “Option” >

“CI setting” > “CI menu”.

• This menu is only available for digital stations.

• The content of this menu depends on the provider

of the CI module.

Module

General information on CI module displays.

Adjustment parameters of each CA card displays.

Enquiry

You can input numerical values such as passwords

here.

Quick guide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp LC-80LE857E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp LC-80LE857E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info