Bedienungsanleitung Sharp lc40le700e (Seite 13 von 52) (Englisch)

144647

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Quick guide

Checking signal strength and

channel strength (DVB-T/C)

If you install a DVB-T/C antenna for the first time or

relocate it, you should adjust the alignment of the

antenna to receive a good reception while checking the

antenna setup screen.

Go to “MENU” > “Setup” > “Antenna setup-

DIGITAL”.

Checking signal strength

Press a/b to select “Signal strength”, and

then press ;.

Supply voltage

CH no.

Current Max.

Signal strength

Channel strength

Current Max.

Quality

Checking channel strength

Press a/b to select “Channel strength”, and

then press ;.

You can input a specified frequency band using the 0_9

numeric buttons.

•

Channel strength of DVB-T

Supply voltage

CH no.

Current Max.

Signal strength

MHz

Signal strength

Channel strength

Current Max.

Quality

Channel strength of DVB-C

Supply voltage

Current

Max.

Signal strength

MHz

Signal strength

Frequency

Symbol rate

QAM modulation

Channel strength

Current Max.

Quality

Position and align the antenna so that

the maximum possible values for “Signal

strength” and “Quality” are obtained.

NOTE

The values of “Signal strength” and “Quality” indicate when to

check the appropriate alignment of the antenna.

•

Inserting the CA card into the CI module

In order to receive coded digital stations, a common interface module (CI module) and a CA card must be inserted in the

CI slot of the TV.

Carefully insert the CI module in

the CI slot with the contact side

forward.

The logo on the CI module must

be facing outward from the rear

of the TV.

Checking CI module information

Go to “MENU” > “Digital setup” > “CI menu”.

This menu is only available for digital stations.

The content of this menu depends on the provider of the CI module.

Module

General information on CI module displays.

Adjustment parameters of each CA card displays.

Enquiry

You can input numerical values such as passwords here.

•

NOTE

Only the LC-32LE705E, LC-32LE705S, LC-40LE705E, LC-40LE705S, LC-46LE705E, LC-46LE705S, LC-32LX705E, LC-40LX705E, LC-

46LX705E, LC-32LU705E, LC-32LU705S, LC-40LU705E, LC-40LU705S, LC-46LU705E and LC-46LU705S models are compatible with

the Common Interface (CI) standard as well as the enhanced security Common Interface Plus (CI+) standard.

It takes about 30 seconds to certify the license key when you insert a CA card into the CI+ compatible CI module for the first time. This

process may fail when there is no antenna input or you have never run “Auto installation”.

The CI+ compatible CI module sometimes upgrades its firmware. You may not receive any TV images before upgrading. You can only use

the power button during upgrading.

The CI+ compatible CI module does not allow you to output any copy protected programmes using monitor out. In this case, the copy

protect icon* is shown in the programme information when P. INFO is pressed.

Protect icon: X

If the TV displays an update confirmation message for the CA card while receiving CI+ compatible broadcasts, follow the screen prompts.

Make sure that the CI module is properly inserted.

•

LC-LE705E_GB.indd 11LC-LE705E_GB.indd 11 2009/10/09 14:12:582009/10/09 14:12:58

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp lc40le700e Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp lc40le700e

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info