Bedienungsanleitung Sharp QW-D52I472X (Seite 25 von 28) (Englisch)

655002

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

EN-25

If one of the program monitor lights is on and start/pause light is on and off,

Your machine’s door is open, shut the door.

If the programme won’t start

• Check if the plug is connected.

• Check your indoor fuses.

• Be sure that the water inlet tap is turned on.

• Be sure that you have closed the machine door.

• Be sure that you switched off the machine by pressing the Power On / Off button.

• Be sure that the water inlet lter and the machine lters are not clogged.

If the lamps “Wash/Dry” and “End” keep ashing

• The water overow alarm is active

• Turn off your tap and contact an authorised service.

If the control lamps won’t go out after a wash operation

Check if the Power On/Off button is released.

If detergent residues are left in the detergent compartment

Detergent has been added when the detergent compartment was wet.

If water is left inside the machine at the end of the programme

• The water drain hose is clogged or twisted.

• The lters are clogged.

• The programme is not nished yet.

If the machine stops during a wash operation

• Power failure.

• Water inlet failure.

• Program can be on standby mode.

If shaking and hitting noises are heard during a wash operation

• Dishes placed incorrectly.

• Spray arm hitting the dishes.

If there are partial food wastes left on the dishes

• Dishes placed incorrectly into the machine, sprayed water did not reach related places.

• Basket overly loaded.

• Dishes leaning against one another.

• Small amount of detergent added.

• An unsuitable, rather weak wash programme selected.

• Spray arm clogged with food wastes.

• Filters clogged.

• Filters incorrectly tted.

• Water drain pump clogged.

CHAPTER -9: FAILURE CODES AND WHAT TO DO IN CASE OF

FAILURE

ERROR

CODE

ERROR

DESCRIPTION

CONTROL

Inadequate water

supply

• Make sure the water input tap is totally open and that there is no

water cut.

• Close the water input tap, separate the water input hose from the

tap and clean the lter at the connection end of the hose.

• Restart your machine, contact the service if the error resumes.

Error of continuous

water input

• Close the tap.

• Contact service.

The waste water in the

machine cannot be

discharged.

• Water discharge hose is clogged.

• The lters of your machine might be clogged.

• Power off-on your machine and activate the program

cancellation command.

• If the error continues, contact the service.

F8 Heater error • Contact service.

Alarm is active against

water overow

• Power off your machine and close the tap.

• Contact service.

FE Faulty electronic card • Contact service.

Overheating error

(temperature in the

machine is

too high)

• Contact service.

F9 Divisor position error • Contact service.

F6 Faulty heater sensor • Contact service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp QW-D52I472X Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info