Bedienungsanleitung Sharp R-756 (Seite 6 von 32) (Englisch)

480393

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

INSTALLATION

WARNING:

Inspect the Oven:

• Check the oven carefully for damage

before and regularly after installation.

• Make sure the door closes properly,

that it is not misaligned or warped.

• Check the hinges and door safety

latches are not broken or loose.

• Ensure the door seal and sealing

surfaces are not damaged. If the door

or door seals are damaged, the oven

must not be operated until it has been

repaired by a competent person.

• Inspect the oven interior and door for

dents.

IMPORTANT:

If any damage is apparent, do not

operate the oven in any way, until it

has been repaired by a SHARP trained

engineer.

1. Remove all packing materials including the

feature sticker (if applicable). Do not remove

the plastic film from the inside of the oven

window as this protects it from dirt. The

waveguide cover prevents food and grease

from entering the waveguide area where it

could cause damage. DO NOT REMOVE

THE WAVEGUIDE COVER.

2. Place oven on a secure, level surface.

Ensure it is strong enough to take the oven

weight, plus the heaviest item likely to be

cooked in the oven.

3. The minimum

height of free

space necessary

above the top

surface of the oven

is 15cm.

4. Do not place the oven where heat, moisture

or high humidity are generated, (for example,

near or above a conventional oven) or near

combustible materials (for example, curtains).

Do not block or obstruct air vent openings.

Do not place objects on top of the oven.

5. Make sure the power supply cord

is undamaged (See “ELECTRICAL

CONNECTION” below).

Do not allow the power supply cord to

run over any hot or sharp surfaces, such

as the hot air vent area at the top rear

of the oven.

6. The socket must be readily accessible so that

it can be easily unplugged in an emergency.

7. Do not use the oven outdoors.

BUILDING-IN-KIT.

No built-in kit is available for this oven.

This oven is designed to be used on a countertop

only.

ELECTRICAL CONNECTION.

• Do not allow water to come into contact with

the power supply cord or plug.

• Insert the plug properly into the socket.

• Do not connect other appliances to the same

socket using an adaptor plug.

• If the power supply

cord is damaged, it must be

replaced by a Sharp approved service facility or

a similarly qualified person to avoid a hazard.

• When removing the plug from the socket

always grip the plug, never the cord as this

may damage the power supply cord and the

connections inside the plug.

• If the plug fitted to your oven is a rewireable

type and in the event of the socket outlet in

your home not being compatible with the plug

supplied, remove the plug properly (do not cut

off).

• If the plug fitted to your oven is a non-rewirable

type and in the event of the socket outlet in

your home not being compatible with the plug

upplied, cut-off the mains plug.

• Refit with a suitable type, observing the wiring

code given in ‘To replace the mains plug’ on

page 27.

15cm

R-756 10/23/2010 11:57:51

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp R-756 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info