Bedienungsanleitung Sharp UL-C10EA-W (Seite 11 von 96) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

787869

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

No air blown out from air conditioner

Cause / Action

• Whether air outlet or air inlet is blocked? / Eliminate the obstacles.

• Under heating mode, whether indoor temperature increase set

temperature? (Cool and Heat model only) / The unit will stop blowing fan

after reaching set temperature.

• Whether heating mode is started up just now? (Cool&Heat model only)

/ In order to prevent cold air, air conditioner will delay for a while to be

started up, which is the normal phenomenon.

• Whether evaporator is defrosted? (conrm this by pulling out the

lter) / It's the normal phenomenon. Air conditioner is defrosting. After

defrosting is nished, it will resume operation.

Set temperature can't be adjusted.

Cause / Action

• Whether the unit operates under auto mode? / Temperature can't be

adjusted under auto mode.

• Whether the required temperature exceeds the temperature setting

range? / Temperature setting range: 16°C to 30°C

• Whether the unit is turned on or turned o just now? / There's owing

sound of refrigerant inside the air conditioner, which is the normal

phenomenon.

Error codes

It is possible for error codes to appear in the display. If they do, take the

appropriate action as shown below.

F1, F2, F4, F0:

Please contact qualied professionals for service.

E8, H3

1. Check if the unit is under high-temperature and high-humidity

environment; if ambient temperature is too high, power o the unit

and then energize it for operation after the ambient temperature drops

to 35°C below.

2. Check if the evaporator and condenser are blocked by some objects;

if yes, take away the objects, power o the unit and then energize it

for operation.

3. If the malfunction still occur, please contact service center.

1. Drain the water inside chassis.

2. If "H8" still exist, please contact the dealer to maintain the unit.

WARNING!

• If any of the phenomenon listed below occur, turn o the air conditioner

and disconnect the power immediately, and then contact the dealer

immediately.

Power cord is overheating or damaged

Abnormal sound during operation

Odors

Water leakage

• Do not repair or ret the air conditioner by yourself.

• If operate the air conditioner under abnormal condition, it may cause

malfunction, electric shock or re hazard.

Installation Precautions

WARNING!

• Observe all governing codes and ordinances.

• Do not use damaged or non-standard power cord.

• Be caution during installation and maintenance. Prohibit incorrect

operation to prevent electric shock, casualty and other accidents.

Selection of installation location

Basic requirement

Installing the unit in the following places may cause malfunction. If it is

unavoidable, please consult your dealer for advice.

1. Locations with high temperature heat sources, vapors, ammable or

explosive gas, or volatile objects spread in the air.

2. Anywhere which has high-frequency devices installed (such as welding

machine, medical equipment).

3. Near to a coastal area.

4. Anywhere which has oil or fumes in the air.

5. Near to sulfureted gas.

6. Other places with special circumstances.

7. Do not install on unstable or motive base structure (such as truck) or in

a corrosive environment (such as chemical factory).

Requirement of air conditioner

1. Air inlet should be far away from obstacles and do not put any objects

near to the air outlet. Otherwise, it will aect the performance of heat

discharge pipe.

2. Select a location where the noise and outow air emitted by the unit

will not aect your local neighborhood.

3. Please try your best to keep far away from uorescent lamps.

4. Do not install this appliance in a laundry room.

5. Do not install near stairs or steps.

Requirements for electric connection

Safety precaution

1. You must follow the electric safety regulations when installing the unit.

2. Follow your local safety regulations and ensure that the correct

electrical supply is used.

3. If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualied persons in order to avoid a

hazard.

4. Properly connect the live wire, neutral wire and grounding wire of

power socket.

5. Be sure to turn o the power supply before proceeding any work

related to electricity and safety.

6. Do not connect the power before nishing installation.

7. The air conditioner is a class 1 electric appliance and must be correctly

grounded. Please make sure it is always grounded eectively,

otherwise it may cause electric shock.

8. The yellow-green wire or green wire in air conditioner is grounding

wire, which can't be used for other purposes.

9. The grounding resistance should comply with your local electrical

safety regulations.

10. The appliance shall be installed in accordance with your countries

wiring regulations.

11. To be in compliance with IEC 61000-3-11, impedance value of power-

supply system connected to product must be less than or equal to the

allowable maximum value of |Zsys| in the following sheet:

models max |Zsys| unit:ohm

UL-C10EA-W

UL-C12EA-W

UL-Y12EA-W

UL-C10UA-W

0.13

Sharp UL-C10EA-W Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info