5. Attach the printer cover
C
Improper use of batteries could cause
them to burst or leak, which might damage
the interior of the cash register
take the following precautions:
•Be sure that the positive (+) and negative
(-) poles of each battery are oriented
properly
•Never mix batteries of different types.
•Never mix old batteries and new ones.
•Never leave dead batteries in the battery
compartment.
•Remove the batteries if you plan not to
use the cash register for long periods.
•Should a battery leak, clean out the
battery compartment immediately
care not to let the battery fluid come into
direct contact with your skin.
•If an incorrect battery is used, it may
explode or leak.
•For battery disposal, follow the relevant
law or regulation in your country
Installing a Paper Roll
Always install the paper roll even when you set the
register for not printing journal or receipt in REG
mode.
1. Push the printer cover forward and detach it.
2. Place a paper roll in the paper roll cradle so
that the paper unrolls from the bottom.
Tax 1
#/
SBTL
@/TM
@/TM
Tax rate (7.0000%) Min. taxable
amount ($0.11)
Changing Other Settings
Your cash register is pre-programmed so that you
can use it with minimum setup. T
settings, see the appropriate sections.
Initial Settings
Departments 1 to 4:
T
Departments 5 to 8:
Non-taxable. Positive (+). Preset price: 0.00
PLU codes 1-10:
Assigned to dept. 1. Preset price: 0.00
PLU codes 1
Not used
When you program the tax status for a department,
tax will be automatically added to sales of items
assigned to the department according to the
programmed tax status for the department. Y
also enter tax manually
There are two tax programming methods. The tax
rate method uses a straight percentage rate per
dollar
information from your state or local tax offices. Use
the method which is acceptable in your state. Y
can obtain necessary data for tax programming from
your local tax office.
D
D
D
For tax table programming, see "programming"
Tax Rate Programming
The percent rate specified here is used for tax
calculation on taxable subtotals. T
switch to the Z/PGM position and use the following
sequence to program the tax rate:
9
➝
#/
SBTL
➝ T➝
@/TM
➝ R
➝
@/TM
➝ Q ➝
where R and Q represent the following.
R: T
Enter the rate in 6 digits (leading zeros may be
omitted). If the rate is fractional (e.g., 4 3/8%), it
should be converted to its decimal equivalent
(4.375) before entering.
Q: Minimum taxable amount (0.01 to 99.99) x 100
Smallest amount for which tax must be collected. In
some states, sales whose amounts are less than the
minimum taxable amount are not subject to tax. If
amounts $0.01 to $0.10 are not taxed, the value of
Q would be 1
taxable category
Time (2:30 p.m.)
#/
SBTL
#/
SBTL
D
D
D
Always enter the date in 6 digits. For
example, enter
0
3
1
5
0
6
for March
15, 2006. If you change the date format in
the Z/PGM mode, follow the newly specified
format when setting the date.
Checking the Time and Date
You can display the time and date to check if they
are correctly set.
1. Turn the mode switch in the REG position.
2. Press the
@/TM
key once to display the time.
3. Press the
@/TM
key a second time to display the
date.
Programming the T
Before you can proceed with registration of sales,
you must first program the tax that is levied in
accordance with the law of your state. Y
register comes with the ability to program four
different tax rates. In most states, you will only
need to program T
area that has a separate local tax (such as a Parish
tax) or a hospitality tax, your register can be
programmed to calculate these separate taxes.
In order to program the tax to be collected in
accordance with the law of your state, you must
specify the tax rate(s) and minimum taxable
amount(s).
D
D
D
•Always enter the time in 4 digits even when
the hour is in the single digit. For example,
enter
0
6
3
0
for 6:30 a.m.
• 6:30 a.m. prints as “06-30” and 6:30 p.m.
prints as “06-30@”.
Setting the Date
In the Z/PGM mode, enter the date in 6 digits using
the month-day-year format. Press the
#/
SBTL
key once
to continue programming or twice to exit the
program mode.
5. Attach the printer cover
(For receipt printing, step 4 should be omitted.)
Setting the Time
Turn the mode switch to the Z/PGM position and
enter the time in 4 digits (“hhmm” format) using the
24 hour system. Press the
#/
SBTL
key once to continue
programming or twice to exit the program mode.
3. Insert three new AA
Initializing the Cash Register
For your cash register to operate properly
initialize it before programming for the first time.
Follow this procedure.
1. Remove the register from its packing carton.
2. Insert one of the supplied mode keys into the
mode switch and turn it to the REG position.
3. Insert the plug into the AC outlet.
IMPORT
without batteries loaded.
4. The buzzer will sound three times. Now your
cash register has been initialized. The display
will show "0.00" with “ ”.
Installing Batteries
Batteries must be installed in the cash register to
prevent data and programmed contents from being
lost from the memory in case of accidental
disconnection of the
install three new “AA” batteries before programming
and operating the cash register
batteries will last approximately one year
time to replace them, the “l ” symbol will appear on
the display to indicate a low battery voltage. If the
symbol appears, you must replace them within two
days.
Install the batteries according to this procedure with
the AC
1. Push the printer cover forward and detach it.
4. When the batteries are properly installed, “ ”
on the display will disappear
cover
Thank you for purchasing the SHARP Electronic Cash Register Model XE-A102. Please
read this manual carefully before operating your machine. Keep this manual for future
reference. It will help you solve any operational problems that you may encounter
For assistance call
1-800-BE-SHARP
SHARP ELECTRONIC CASH REGISTER
MODEL
XE-A102
INSTRUCTION MANUAL
WARNING
FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when this equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
CAUTION
The socket-outlet shall be installed near the equipment and shall be easily accessible.
FOR YOUR RECORDS
Please record below the model number and serial number
These numbers are located on the right side of the unit. Space is provided for further pertinent data.
Model Number_______________________________________________________
Serial Number_______________________________________________________
Date of Purchase_____________________________________________________
Place of Purchase____________________________________________________
Handling Cautions
Install the cash register in a location not subject to direct sunlight, unusual temperature
changes, high humidity
Do not operate the cash register with wet hands. W
The cash register plugs into any standard wall outlet (120V ± 10%).
other electrical devices on the same electrical circuit since such connection could cause the
cash register to malfunction.
When cleaning the cash register
benzine or thinner
For protection against data loss, please install three new “AA” batteries before using the cash
register
batteries; otherwise damage to memory contents or malfunctioning of the register will occur
can start operating it only after initializing it and then installing batteries.
For complete electrical disconnection, pull out the main plug.
Printed in China
O(TINSE2539RCZZ) 1
Getting Started
For Easy Set-up,
See “Getting Started”
View from rear
View from rear
2. Open the battery cover next to the paper roll
cradle.
3. Insert the paper straight into the paper inlet,
and press the
f
f
f key
comes out at the printing area.
4. (For journal printing) Insert the top end of
the paper into the slit in the take-up spool
shaft and wind the paper two or three turns.
Then place the take-up spool on the bearing.
Date (March 15, 2006)
#/
SBTL
#/
SBTL
