Bedienungsanleitung Sharp XEA201 (Seite 41 von 105) (Englisch, Spanisch)

17268

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

The register allows you to program the texts for clerk names, department item names, PLU/subdepartment item

names, and so on, if necessary. There are two ways for programming text: using character keys on the

keyboard or entering character codes with numeric keys on the keyboard.

Using character keys on the keyboard

You can enter characters according to the small figures printed in the lower right position of the key tops. For

the layout, please refer to “Keyboard” section on page 5.

The following are used as control keys for character entry:

Toggles between upper-case and lower-case letters. By default, the upper-case letter is selected.

Once the

key is pressed, you are locked in for entering lower-case letters. “_” lights up at the

SHIFT position of the display when lower-case letters entry is selected.

Press the

key to enter numeric characters. For example to enter “1”, press the

and

key. If you press the

key without pressing the

key, the cash register goes to character codes

entry mode.

Once the

key is pressed, you are locked in for entering numeric characters. “_” lights up at the

NUMBER position of the display when numeric characters entry is selected.

Toggles between single-size and double-size characters. By default, the single-size character is

selected. Once the

key is pressed, you are locked in for entering double size characters. “_” lights

up at the DC position of the display when double-size characters entry is selected.

Backs up the cursor, erasing the character to the left.

To program the word “Clerk01” with the letter “C” being double size.

To make the letter “C” double size character

To make character size return to normal size

To toggle the characters to lower-case letters

hijk

To enter numbers

N01

Entering character codes with numeric keys on the keyboard

Numerals, letters and symbols are programmable by entering the character code and the

key. (If numeric

characters entry is selected, that is, “_” lights up at the NUMBER position of the display, press the

key to

release it.) Set the alphanumeric character code table on the next page. By doing this, you can program

characters other than those on the key tops.

• Double-size characters can be made by entering the character code 253.

• All three digits of the character code MUST be entered (even if it starts with zero).

To program the word “SHARP” in double-size characters

When you press an appropriate number key (job code number) and press the

key for text entry just after you

start programming with the

key, the cash register will be automatically ready for text entry.

Listed below is an overview of what you can program and the allowable number of single sized characters for

each text entry.

• Department text 12 characters

• PLU text (item label) 12 characters

• Function text 8 characters

• Logo message 6 lines and 24 characters for each line

• Clerk name 8 characters

• Foreign currency symbol 4 characters

253

083

072

065

082

080

S H A R P

Text Programming

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XEA201 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XEA201

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info