Bedienungsanleitung Sharp XEA301 (Seite 77 von 80) (Englisch)

17286

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

The malfunctions shown in the left-hand column below, labelled “Fault,” do not necessarily indicate functional

faults of the machine. It is therefore advisable to refer to “Checking” shown in the right-hand column before

calling for service.

Error message table

When the following error messages are displayed, press the

key and take a proper action according to the

table below.

Fault Checking

The display won’t illuminate even when the mode switch

is turned to any other position than “ ”.

• Is power supplied to the electrical outlet?

• Is the power cord plug out or loosely connected to the

AC outlet?

(2)

The display shows symbols that do not make sense. • Has the machine been initialized properly as shown in

“GETTING STARTED”?

(Note that initialization clears all the data and programmed

settings stored in memory.)

(1)

The display is illuminated, but the whole machine

refuses registrations.

• Is a clerk code assigned to the register?

• Is the mode switch set properly at the “REG” position?

(3)

No receipt is issued. • Is the paper roll properly installed?

• Is there a paper jam?

• Is the receipt function in the “OFF” status?

• Is the print head release lever at the printing position?

(4)

No journal paper is taken up. • Is the take-up spool installed on the bearing properly?

• Is there a paper jam?

(5)

Printing is unusual. • Is the print head release lever at the printing position?

• Is the paper roll properly installed?

(6)

Before Calling for Service

Error message Error status Action

ENTRY ERROR Registration error Make a correct key entry.

MISOPERATION Misoperation error Make a correct key entry.

NO RECORD Undefined code is entered. Enter a correct code.

MEMORY FULL Memory is full (in the AUTO key programming). Program the AUTO key within 25 steps.

SBTL COMPUL. Compulsory depression of the

key for Press the

key and continue the operation.

direct finalization

TEND COMPUL. Compulsory tendering Make a tendering operation.

NOT ASSIGNED No entry of a clerk code Make a clerk code entry.

OVER LIMIT. Overflow limitation error Make a registration within a limit of entry.

INH. OPEN PR The open price entry is inhibited. Make a preset price entry.

INH. UNIT PR The preset price entry is inhibited. Make an open price entry.

NOT NON-TEND The direct finalization is inhibited. Make a tendering operation.

BUFFER FULL Subtotal void is not allowed. Finalize the transaction, and correct the wrong

entries in the

mode.

HEAD UP Print head release lever is lifted up. Move the lever toward the take-up spool (to the

printing position).

PAPER EMPTY Receipt and/or journal paper roll is not Install a receipt and/or journal paper.

installed or empty.

CLERK ERR. CCD compulsory Make CCD operation.

A301_5(En) 03.4.24 7:45 PM Page 75

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XEA301 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XEA301

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info