Bedienungsanleitung Sharp XG-C465X-L (Seite 68 von 73) (Englisch)

543351

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

-66

Troubleshooting

Check

• Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

• The AV MUTE function is working.

• Cables incorrectly connected to the rear panel of the projector.

• Remote control batteries have run out.

•

External output has not been set when connecting notebook computer.

• The filter cover, lamp unit cover or lamp housing cover is not

installed correctly.

• If the connected DVI digital equipment is turned on before the

“DVI-D” input mode is selected on the projector, the image may

not be projected properly or may not be displayed at all. Ensure

that the appropriate input mode has been selected on the

projector before you turn on the connected equipment.

• Cables incorrectly connected to the rear panel of the projector.

• “Bright” is set to minimum position.

• Depending on the computer you are using, an image may not

be projected unless the signal output setting of the computer is

switched to the external output. Refer to the computer’s

operation manual for how to switch its signal output settings.

• Image adjustments are incorrectly set.

(Video, S-Video Input only)

• Video input system is incorrectly set.

(COMPUTER/COMPONENT 1, 2, DVI-D only)

• Input signal type (RGB/Component) is incorrectly set.

• Adjust the focus.

• The projection distance exceeds the focus range.

• There is fog on the lens. If the projector is carried from a cold

room into a warm room, or if it is suddenly heated,

condensation may form on the surface of the lens and the

image will become blurred. Please set up the projector at least

one hour before it is to be used. If condensation should form,

remove the power cord from the wall outlet and wait for it to

clear.

(Computer Input only)

• Perform “SIG-ADJ” Adjustments. (“Clock” Adjustment)

• Perform “SIG-ADJ” Adjustments. (“Phase” Adjustment)

• Noise may appear depending on the computer.

• Cables incorrectly connected to the rear panel of the projector.

• Volume is set to minimum.

• When the projector is connected to an external device and the

volume is set to minimum, the sound is not output even if you

turn up the volume of the external device.

• “Speaker” is set to “Off”.

• Make the necessary adjustments of each item in the “SIG-ADJ”

menu.

• Depending on the computer you are using, the output resolution

signal may be different from the one you have set. For details,

refer to the operation manual of the computer.

Problem

Data image is not

centered.

Page

—

23-29

—

23-29

—

No picture and no sound

or projector does not start.

Color is faded or poor.

Picture is blurred;

noise appears.

Sound is heard but no

picture appears.

Picture appears but no

sound is heard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XG-C465X-L Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info