Bedienungsanleitung Sharp XG-C465X (Seite 13 von 45) (Englisch)

469870

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

-13

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,

commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard. Parity bit: None

Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit

Data length: 8 bits Flow control: None

*Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After

the projector processes the command from the computer, it sends a response code to the computer.

Info

• When controlling the projector using RS-232C commands from a computer, wait for at least 40 seconds

after the power has been turned on, and then transmit the commands.

• After sending an input selection or picture adjustment command and then receiving an “OK” response

code, the projector may take some time to process the command. If a second command is sent while the

projector is still processing the first command, you may receive an “ERR” response code. If this happens,

try resending the second command.

• When more than one code is being sent, send each command only after the response code for the previ-

ous command from the projector is verified.

• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1” “TLTL _ _ _ 1”

“TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”

−

When the projector receives the special commands shown above:

* The on-screen display will not disappear.

* The “Auto Power Off” timer will not be reset.

−

The special commands are available for applications that require continuous polling.

Return code (0DH)

C1 C2 C3 C4 P1 P2 P3 P4

Response code format

Normal response

Problem response (communication error or incorrect command)

O K

E R R

Command 4-digit Parameter 4-digit

Command format

Return code (0DH)

Return code (

0DH)

RS-232C Specifications and Commands

Note

• If an underbar (_) appears in the parameter column, enter a space.

• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under

Control Contents.

*1 Serial No. Check command is used to read out the 12 digits of serial No..

*2 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.

*3 Parameters of CLR Temp settings are as follows.

*4 The adjustable range of “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.

CLR Temp

5500K

6500K

7500K

Parameter

_0 5 5

_0 6 5

_0 7 5

CLR Temp

8500K

9300K

10500K

Parameter

_0 8 5

_0 9 3

_1 0 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XG-C465X Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XG-C465X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info