Bedienungsanleitung Sharp XG-C465X (Seite 10 von 71) (Englisch)

469870

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

-8

Ensure that you read the following safeguards when

setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass par-

ticles if lamp ruptures. In case

of lamp rupture, contact your

nearest Sharp Authorized Pro-

jector Dealer or Service Cen-

ter for replacement.

See “Replacing the Lamp” on

page 60.

Caution concerning the setup of the pro-

jector

■ For minimal servicing and to maintain high

image quality, SHARP recommends that this

projector be installed in an area free from hu-

midity, dust and cigarette smoke. When the

projector is subjected to these environments,

the vents and lens must be cleaned more

often. As long as the projector is regularly

cleaned, use in these environments will not

reduce the overall operation life of the unit.

Internal cleaning should only be performed

by a Sharp Authorized Projector Dealer or

Service Center.

Do not set up the projector in places ex-

posed to direct sunlight or bright light.

■ Position the screen so that it is not in direct

sunlight or room light. Light falling directly on

the screen washes out the colors, making

viewing difficult. Close the curtains and dim

the lights when setting up the screen in a

sunny or bright room.

The projector may be safely tilted to a

maximum angle of 9 degrees.

■ Placement should be within ±9 degrees of

horizontal.

When using the projector in high-altitude

areas such as mountains (at altitudes of

approximately 1,500 meters (4,900 feet)

or more)

■ When you use the projector in high-altitude

areas with thin air, set “Fan Mode” to “High”.

Neglecting this can affect the longevity of the

optical system.

Warning about placing the projector in a

high position

■ When placing the projector in a high posi-

tion, make certain it is carefully secured to

avoid personal injury caused by the projec-

tor falling down.

Do not subject the projector to hard im-

pact and/or vibration.

■ Ta ke care with the lens so as not to hit or

damage the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long

hours will cause eye strain. Take regular

breaks to rest your eyes.

Avoid locations with extremes of tem-

perature.

■ The operating temperature of the projector

is from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is

from –4°F to 140°F (–20°C to +60°C).

Do not block the intake and exhaust

vents.

■ Allow at least 7

/8 inches (20 cm) of space

between the exhaust vent and the nearest

wall or obstruction.

■ Ensure that the intake vent and the exhaust

vent are not obstructed.

■ If the cooling fan becomes obstructed, a pro-

tection circuit will automatically put the pro-

jector into standby mode to prevent overheat

damage. This does not indicate a malfunc-

tion (see pages 58 and 59). Remove the pro-

jector power cord from the wall outlet and wait

at least 10 minutes. Place the projector where

the intake and exhaust vents are not blocked,

plug the power cord back in and turn on the

projector. This will return the projector to the

normal operating condition.

CAUTION

PRECAUCIÓN

PRÉCAUTION

IMPORTANT SAFEGUARDS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XG-C465X Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XG-C465X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info