Bedienungsanleitung Sharp XG-P610X-N (Seite 82 von 86) (Englisch)

469885

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

-80

CheckProblem Page

An unusual sound is

occasionally heard

from the cabinet.

Maintenance

indicator illuminates or

blinks in red.

The projector cannot be

turned on or put into the

standby mode using the

ON or STANDBY button

on the projector.

All buttons on the

projector and the remote

control are unavailable.

Picture is green on

COMPUTER 1or 2

(COMPONENT).

Picture is pink (no green)

on COMPUTER 1/ 2 or

DVI (RGB).

The black levels of the

image show banding or

appear faded when DVI

or HDMI is selected.

Picture is too bright and

whitish.

The cooling fan

becomes noisy.

The lamp does not light

up even after the

projector turns on.

The lamp suddenly turns

off during projection.

The image sometimes

flickers.

The lamps take a long

time to turn on.

Picture is dark.

The remote control

cannot be used.

• If the picture is normal, the sound is due to cabinet shrinkage

caused by room temperature changes. This will not affect

operation or performance.

• See “Maintenance Indicators”.

• If the “Keylock Level” menu is set to “Level A” or “Level B”, all or

specific buttons on the projector are unavailable. Use the

remote control to operate the projector.

• If the “Stack Setting” menu is set to “Slave” and the “Keylock

Level” menu is set to “Level B”, all buttons on the projector and

the remote control are unavailable. Connect the remote control

to the projector, and then use the remote control to operate the

projector.

• Change the input signal type setting.

• Make adjustments that result in the best picture quality in the

“Dynamic Range” setting.

• Image adjustments are incorrectly set.

• When temperature inside the projector increases, the cooling

fan runs faster.

• The lamp indicator is illuminating in red.

Replace the lamp.

• Cables are incorrectly connected to the projector or the

connected equipment works improperly.

• If this happens frequently, replace the lamp.

• The lamps will eventually need to be changed.

The lamps have reached the end of its life. Replace the lamps.

• Operate the remote control while pointing it at the projector’s

remote control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent light is shining on the

projector’s remote control sensor, place the projector where it

will not be affected by strong light.

• Is a ø3.5 mm minijack cable plugged into the WIRED REMOTE

terminal?

• The batteries may be depleted or inserted incorrectly. Make

sure the batteries are inserted correctly or insert new ones.

—

9, 10

66, 69, 70

24–27

This projector is equipped with a microprocessor. Its performance could be adversely affected by incorrect op-

eration or interference. If this should happen, unplug the projector and plug it in again after more than 5 minutes.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XG-P610X-N Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XG-P610X-N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info