Bedienungsanleitung Sharp XG-P610X-N (Seite 14 von 59) (Englisch)

469885

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

-14

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,

commercially available) to the projector. (See page 27 of the projector’s operation manual for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard. Parity bit: None

Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit

Data length: 8 bits Flow control: None

*Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After

the projector processes the command from the computer, it sends a response code to the computer.

Info

• When you have more than one command to give to the projector, send each of them only after the re-

sponse code for the previous one is received.

• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TLPS _ _ _ 2” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”

“TLTT _ _ _ 2” “TLTM _ _ _ 1” “TLTM _ _ _ 2” “TLTL _ _ _ 1” “TLTL _ _ _ 2” “TNAM _ _ _ 1” “MNRD _ _ _ 1”

“SNRD _ _ _ 1” “PJN0 _ _ _ 1”

−

When the projector receives the special commands shown above :

* The on-screen display will not disappear.

* The “Auto Power Off” timer will not be reset.

−

The special commands are available for applications that require continuous polling.

(Do not repeatedly or periodically send any commands other than these special commands in STANDBY

mode as it will cause problems.)

Note

• When controlling the projector using the RS-232C commands, you cannot confirm the projector setting

values from the computer. To confirm each setting value, send the display command for each menu (e.g.

RARE _ _ _ 0), and then refer to the on-screen display. When using the setting/adjustment commands other

than the menu display commands, the settings/adjustments are executed without the on-screen display.

• If an underbar (_) appears in the parameter column, enter a space.

• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under

Control Contents.

PJLink

Compliant:

This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.

This product confirms with the PJLink standard specification version 1.00.

For additional information, visit “http://pjlink.jbmia.or.jp/english/”.

Return code (0DH)

C1 C2 C3 C4 P1 P2 P3 P4

Response code format

Normal response

Problem response (communication error or incorrect command)

O K

E R R

Command 4-digit Parameter 4-digit

Command format

Return code (0DH)

Return code (

0DH)

RS-232C Specifications and Commands

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XG-P610X-N Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XG-P610X-N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info