Bedienungsanleitung Sharp XG-P610X-N (Seite 33 von 59) (Englisch)

469885

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

-33

Setting the Projector Using RS-232C or Telnet

SETUP MENU (Main Menu)

[1]IP Address (Factory default setting : 192.168.150.2)

IP address settings. (Page 36)

[2]Subnet Mask (Factory default setting :

255.255.255.0)

Subnet mask settings. (Page 36)

[3]Default Gateway (Factory default setting : Not

Used)

Default gateway settings. (Page 36)

[4]User Name (Factory default setting : Not Re-

quired)

Setting of user name for security protection. (Page 36)

[5]Password (Factory default setting : Not Required)

Setting of password for security protection. (Page 37)

[6]RS-232C Baud Rate (Factory default setting :

9600 bps)

Baud rate settings for the RS-232C terminals. (Page

37)

[7]Projector Name

It is possible to assign a projector name. (Page 37)

[8]DHCP Client

DHCP Client settings. (Page 37)

[A]Advanced Setup

Enters ADVANCED SETUP MENU. (Page 38)

[D]Disconnect All

Disconnect all connections. (Page 38)

[V] View All Setting

Displays all setting values. (Page 34)

Can also be used with ADVANCED SETUP MENU.

[S] Save & Quit

Save set values and quit menu. (Page 35)

[Q]Quit Unchanged

Quit menu without saving setting values. (Page 35)

Note

• The factory default settings for the projector are

as follows:

DHCP Client : OFF

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

ADVANCED SETUP MENU

[1]Auto Logout Time (Factory default setting : 5 min-

utes)

Setting of time until automatic disconnection of net-

work connection. (Page 38)

[2]Data Port (Factory default setting : 10002)

Setting the TCP port number used when exchang-

ing data. (Page 38)

[5]Network Ping Test

It is possible to confirm that a network connection

between the projector and a computer etc. is work-

ing normally. (Page 39)

[6]Accept IP Addr(1)

[7]Accept IP Addr(2)

[8]Accept IP Addr(3)

[9]Accept All IP Addr (Factory default setting : Ac-

cept All)

For improved security, it is possible to set up to three

IP addresses allowing connection to the projector.

Set IP addresses can be cancelled using [9] Accept

All IP Addr. (Page 39)

[0] Search Port (Factory default setting : 5006)

Setting the port number used when searching for

the projector. (Page 40)

[!] Restore Default Setting

Restores all setting values that can be set using the

menu to the default state. (Page 40)

[Q]Return to Main Menu

Return to the main SETUP MENU. (Page 40)

▼SETUP MENU ▼ADVANCED SETUP MENU

---------------------------------SETUP MENU--------------------------------

[1]IP Address [2]Subnet Mask [3]Default Gateway

[4]User Name [5]Password

[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client

[A]Advanced Setup [D]Disconnect All

[V]View All Setting [S]Save & Quit [Q]Quit Unchanged

setup>

******************** ADVANCED SETUP MENU ***********************

[1]Auto Logout Time [2]Data Port

[5]Network Ping Test

[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr [0]Search Port

[!]Restore Default Setting

[Q]Return to Main Menu

advanced>

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XG-P610X-N Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XG-P610X-N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info