Bedienungsanleitung Sharp XL-BB20D (Seite 21 von 136) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

679563

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

EN-20

Enhancing your system

The connection lead is not included. Purchase a commer-

cially available lead as shown below.

Audio cable (not supplied)

Portable audio

player, etc.

■ Listening to the playback sounds of

portable audio player, etc.

Use a connection lead to connect the portable audio

player, etc. to the AUDIO IN socket.

2 Press the

(ON/STANDBY)

button to turn the power on.

3 Press the INPUT (AUDIO/LINE (INPUT)) button (main

unit or remote control) repeatedly to select AUDIO IN

function.

4 Play the connected equipment. If volume level of the

connected device is too high, sound distortion may

occur. Should this happen, adjust the volume of the

connected device.

Note:

To prevent noise interference, place the unit away from

the television.

■ Headphones

● Do not set the volume on to maximum at switch on.

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

● Before plugging in or unplugging the headphone, re-

duce the volume.

● Be sure your headphone has a 3.5 mm diameter plug

and impedance between 16 and 50 ohms. The recom-

mended impedance is 32 ohms.

● Plugging in the headphone disconnects the speakers au-

tomatically.

Troubleshooting chart

If something is wrong with this product, check the following be-

fore calling your authorised SHARP dealer or service centre.

■ General

Symptom Possible cause

● The clock is not set to

the correct time.

● A power failure occurred.

Reset the clock. (Refer

page 8)

● When a button is

pressed, the unit does

not respond.

● Set the unit to the power

standby mode and then

turn it back on.

● If the unit still malfunc-

tions, reset it. (Refer page

21)

● No sound is heard. ● The volume level set to

“Volume Min”.

● The headphones are con-

nected.

■ Remote control

Symptom Possible cause

● The remote control

does not operate.

● The AC power lead of the

unit is not plugged in.

● The battery polarity is

wrong.

● The batteries are dead.

● The distance or angle is

incorrect.

● The remote control sensor

receives strong light.

■ Tuner/DAB

Symptom Possible cause

● The radio makes

unusual noises con-

tinuously.

● The unit placed near a TV

or computer.

● The FM/DAB aerial is not

placed properly. Move the

aerial away from the AC

power lead if it is located

nearby.

● “Station Full” appears

when performing DAB

manual tune.

● Station storage is full.

To recover, perform Auto

Scan. (Refer page 16)

■ Bluetooth

Symptom Possible cause

● No sound is heard. ● The unit is too far from the

Bluetooth audio source

device.

● The unit is not paired

with the Bluetooth audio

source device.

● Bluetooth sound is in-

terrupted or distorted.

● The unit is too near to

a device that generates

electromagnetic radiation.

● There is an obstacle

between the unit and the

Bluetooth audio source

device.

XL-BB20D_OM_EN_DE_ES_FR_IT_PL.indb 20 2018-01-25 10:10:00

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XL-BB20D Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XL-BB20D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info