Bedienungsanleitung Sherwood R-904 (Seite 25 von 51) (Englisch)

489151

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

ENGLISH

■When selecting the “D.VOL (Dolby Volume)”

• Dolby Volume is an intelligent system that improves the perceived audio frequency response at lower listening levels and

corrects for volume inconsistencies between sources (e.g. a jazz radio station and a DVD) and between programming (e. g. a

TV show and advertisement breaks).

OFF (Default value) : To turn off the Dolby Volume function. (The DOLBY VOLUME indicator goes off.)

↕

ON : To turn it on. (The DOLBY VOLUME indicator lights up.)

• If the Dolby Volume is set to ON, it will be automatically turns on the Volume Modeler that maintains the same perceived

listening experience as the reference level experience.

■Note :

• If the Dolby Volume is changed to OFF, the volume level may be increased high.

◆When the Dolby Volume is set to ON

①. Press the ENTER button to enter the Dolby Volume setup.

• Then “LVL (Volume Leveler)” is displayed for several seconds.

②. Press the CURSOR UP/DOWN buttons to select the desired parameter.

• Each time these buttons are pressed, the parameter mode changes as follows :

→ “LVL” ↔ “AMOUNT” ←

(Volume Leveler) (Volume Leveler Amount Control)

→ “C/O” ↔ M/S ↔ HALF ←

(Calibration Offset) (Mid/Side mode) (Half mode)

③. Press the CURSOR LEFT/RIGHT buttons to adjust the selected parameter as desired.

◆When selecting the “LVL” (Volume Leveler)

• The Volume Leveler maintains the perceived loudness of all content for example, from different channels or input sources.

OFF : To turn off the Volume Leveler function.

↕

ON (default value) : To turn it on.

■Note :

• If Volume Leveler is turned off, no level matching between sources and program material is performed. This is not the same as

turning Dolby Volume off as volume related frequency response processing is still active.

◆When selecting the “AMOUNT” (Volume Leveler Amount Control)

The Volume Leveler Amount adjusts the amount of leveling applied by the Volume Leveler.

• The control can be set in 11 steps from 0 to 10 (default value : 9)

◆When selecting the “HALF” (Half mode)

If the Half mode is set to ON, the Volume Modeler does not apply volume contour gains for playback levels higher than reference

level; just the volume setting, as a flat spectrum gain, is applied.

OFF (default value) : To turn off the Half mode.

↕

ON : To turn it on.

◆When selecting the “M/S” (Mid/Side mode)

The Mid/Side processing can improve stability of some stereo material.

OFF (default value) : To turn off the Mid/Side mode.

↕

ON : To turn it on.

◆When selecting the “C/O” (Calibration Offset)

The Calibration Offset allows you to compensate for speaker efficiencies and listening position.

• The control can be set from -15 to +15 dB (default value : 0 dB) and this should normally produce a good result when you set

the speaker levels on this receiver using a SPL (Sound Pressure Level) meter.

Continued

R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sherwood R-904 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sherwood R-904

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info