Bedienungsanleitung Sherwood RD-8504 (Seite 63 von 71) (Englisch)

459228

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

ENGLISH

Troubleshooting Guide

If a fault occurs, run through the table below before taking your receiver for repair.

If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your

dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the warranty.

PROBLEM POSSIBLE CAUSE REMEDY

No power

o sound

No sound from the surround

speakers

No sound from the center

speaker

No sound from the surround back

speakers

No picture

No picture with an HDMI

connection

Noise or distorted picture

Stations cannot be received

Preset stations cannot be

received

Poor FM reception

Continuous or intermittent hissing

noise during AM reception,

especially at night.

Remote control unit does not

operate.

OSD function is not available.

• The AC input cord is disconnected.

• Poor connection at AC wall outlet or the outlet is

ead or off.

•

The speaker wires are disconnected.

• The master volume is adjusted too low.

• The MUTE button is pressed to ON.

• Incorrect selection of input source.

• Incorrect connections between the components.

•

The HDMI Audio Output is set to HDMI

Passthrough.

•

The settings related to audio are set incorrectly.

• Surround mode is switched off(stereo mode).

• Master volume and surround level are too low.

•

Monaural source is used.

• Surround speaker setting is "No".

• Dolby Virtual Speaker, stereo mode, etc is

selected.

• Center speaker setting is "No".

• Master volume and center level are too low.

• The input signal format or the current surround

mode cannot support the 7.1(or 6.1) surround.

• The surround back channels' power amplifier is

assigned to "Bi AMP" or "Room 2".

• Master volume and surround back level are too low.

• Surround back speaker setting is "No".

• Video connections between this unit and the

monitor TV are not made correctly.

• Incorrect selection of input source on the monitor

TV.

• The settings related to video are set incorrectly.

• HDMI connection between this unit and the

monitor TV are not made correctly.

• The monitor TV or other equipments do not

support HDCP.

• Video format of your monitor TV, DVD player, etc.

is different from NTSC.

• No antenna is connected.

• The desired station frequency is not tuned in.

• Antenna is in wrong position.

• An incorrect station frequency has been memorized.

• The memorized stations are cleared.

• No antenna is connected.

• The antenna is not positioned for the best reception.

• Weak signals.

• Noise is caused by motors, fluorescent lamps or

lightning, etc.

• Batteries are not loaded or exhausted.

• The remote sensor is obstructed.

• Video connections between this unit and the

monitor TV are not made correctly.

• Connect cord securely.

•

Check the outlet using a lamp or another

appliance.

• Check the speaker connections.

• Adjust the master volume.

•

Press the MUTE button to cancel the muting effect.

• Select the desired input source correctly.

•

Make connections correctly.

• Set it to Speaker. (For details, refer to "When

selecting the HDMI Audio Output" on page 45.)

• Set the settings correctly. (For details, refer to

"SETTING THE INPUT SETUP" on page 55.)

• Select a surround mode.

•

Adjust master volume and surround level.

• Select a stereo or surround source.

• Select the desired surround speaker setting.

• Select the desired surround mode.

• Select the desired center speaker setting.

•

Adjust master volume and center level.

• Under the proper situations, perform the 7.1(or

6.1) surround playback.(For details, refer to

"ENJOYING SURROUND SOUND" on page 25.)

• Assign the power amplifier to the surround back

channels.(For details, refer to "When selecting

the AMP Assign"on page 45.)

• Adjust master volume and surround back level.

• Select the desired surround back speaker setting.

• Make proper video connections.

• Select the input source correctly.

• Set the settings correctly. (For details, refer to

"SETTING THE INPUT SETUP" on page 55.)

• Make proper HDMI connection.

• This unit will not output video signal unless the

connected equipments supports HDCP.

• Change the video format to NTSC.

• Connect an antenna.

• Tune in the desired station frequency.

• Move antenna and retry tuning.

• Memorize the correct station frequency.

• Memorize the stations again.

• Connect an antenna.

• Change the position of the antenna.

• Install an outdoor FM antenna.

• Keep the receiver away from noise sources.

• Install an outdoor AM antenna.

• Replace the batteries.

• Remove the obstacle.

• Make proper (composite) video connections.

RD-8504(A)_ENG_091118:RD-8504(A)2009-11-18오 6:41페이지63

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sherwood RD-8504 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sherwood RD-8504

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info