Bedienungsanleitung Showtec Atmos 1000 (Seite 10 von 12) (Englisch)

810416

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Maintenance

The Atmos 1000 fogger requires almost no maintenance. However, you should keep the unit clean.

Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in

liquid.

Please clean internal components once a year with a light brush and vacuum cleaner. Do not use

alcohol or solvents.

Keep connections clean. Disconnect electric power, and then wipe the connections with a damp cloth.

Make sure connections are thoroughly dry before linking equipment or supplying electric power.

Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid

container and the fog machine liquid tank immediately after filling.

After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of

80% distilled water/20% white vinegar through the system to prevent the accumulation of particulate

matter in the heating element.

When cleaning, use only a clean, lint-free soft cloth. An effective cleaning regimen is as follows:

1. While unit is unplugged and cool, unscrew nozzle at very front of unit and clean out debris with vinegar

and a pipe cleaner, making sure that the hole is free of clogs.

2. Empty all fog fluid from machine. Add cleaning solution to tank. Plug unit in and begin warm up.

3. Run unit in a well-ventilated area until tank is empty.

4. Replace nozzle and refill with liquid.

Performance Notes

• All fog machines develop condensation around the output nozzle. Because this may result in some

moisture accumulation on the surface below the output nozzle, consider this condensation when

installing your unit.

• Fog machines may sputter small amounts of fog occasionally during operation and for a minute or so

after being turned off.

• All fog machines have a recycling period after bursts of fog, when the machine will shut itself down for

a short period in order to heat back up. During this time no fog can be produced.

Troubleshooting

Showtec Atmos 1000 Fogger

This troubleshooting guide is meant to help solve simple problems.

Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can permanently

damage the unit.

If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit

operates properly, do not carry out following steps.

If the fogger does not operate properly, refer servicing to a technician.

1. If you experience low output, pump noise or no output at all, unplug immediately.

2. Check fluid level, the external fuse, remote connection, and power from the wall.

3. If all of the above appears to be O.K., plug the unit in again.

4. If fog does not come out after holding the remote button down for 30 seconds, check the hose

attached to the tank to make sure there is fluid going through the hose. Make sure the fogger isn’t

warming up.

5. If you are unable to determine the cause of the problem, do not simply continue pushing the remote

button, as this may damage the unit.

6. Return the machine to your Showtec dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Showtec Atmos 1000 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Showtec Atmos 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info