Bedienungsanleitung Siemens AL140 (Seite 9 von 12) (Englisch)

63588

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

L1a / GBR / A31008-M2001-L101-1-7619 / AL140_AL145_Kombi_GBR.fm / 12.09.2008

Base station power consumption

General specifications

Care

Wipe the base station, charging cradle and hand-

set with a da

mp cloth (do not use solvent) or an

antistatic cloth.

Never

use a dry cloth. This can cause static.

Contact with liquid

If the handset has come into contact with liquid:

1. Switc

h off the handset and remove the bat-

tery pack immediately.

2. Allow the liquid to drain from the handset.

3. Pat all parts dry, then place the handset with

he battery compartment open and the keypad

facing down in a dry, warm place for at least

72 hours (no

t in a microwave, oven etc.).

4. Do not switch on the handset again until it is

mpletely dry.

When it has fully dried out, you will normally be

able to use it again.

Questions and answers

If you have any questions about using your phone,

visit us at

www.gigaset.com/customercare at any

time. The table below contains a list of common

oblems and possible solutions.

AL140 AL145

In standby mode

– Handset in charging cradle

– Handset out of charging cradle

approx.

1.0 W

approx.

0.8 W

approx.

1.2 W

approx.

1.0 W

During a call approx.

1.0 W

approx.

1.2 W

DECT standard is supported

GAP standard is supported

Range up to 300 m outdoors

up to 50 m indoors

Base station power supply 230 V ~/50 Hz

Environmental conditions

in operation

+5° C to +45 °C;

20% to 75% humidity

Problem Cause Solution

Nothing

appears in

the display.

The handset is not

turned on.

Battery pack is

flat.

Press the end call key

a for approx. 5 sec-

onds or place the

handset in the base

station.

Charge/replace the

batt

ery pack (page 3).

No reaction

to key press.

The keypad lock is

tivated.

Press the hash key

for approx. 2 sec-

onds (page 1).

No wireless

conn

ection to

the base sta-

tion, Ba

flashes in

the display.

The handset is

outside

the range

of the base sta-

tion.

The handset is not

egistered.

The base station is

t turned on.

Cords not routed

cor

rectly.

Move the handset

oser to the base

station.

(page 3).

Check the power con-

nector at the base sta-

tion (page 2).

Check cord routing

(page 2).

You cannot

ear a ringer/

dialling tone

from the fixed

network.

The phone cord

supp

lied has not

been used or has

been replaced by

a new cord with

the wrong jack

connections.

Please always use the

one cord supplied

or ensure that the jack

connections are cor-

rect when purchasing

om a retailer

(page 2).

Error tone

sounds af

ter

system PIN

prompt.

PIN forgotten.

You have entered

the w

rong system

PIN.

Reset the system PIN

to the default 0000.

To do this, unplug the

mains unit from the

mains socket

£Press and hold the

paging key

£Plug the mains

adapter in again

£Hold the paging

key down for at least

another 2 seconds

and then release.

The reset procedure is

now

carried out.

The handsets are de-

registered. The calls

list is

cleared.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens AL140 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens AL140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info