Bedienungsanleitung Siemens AL280 (Seite 14 von 23) (Englisch)

64999

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

AL180-AL185_AL280-AL285 / IM en / A31008-M2003-R101-2-UZ19 / main.fm / 12.11.2010

Specifications

Recommended batteries

Technology: Nickel-metal-hydride (NiMH)

Size: AAA (Micro, HR03)

Voltage: 1.2 V

Capacity: 400–800 mAh

We recommend the following types of battery:

u GP 550/700 mAh

u Yuasa Phone 700/800 mAh

u Peacebay 550/650 mAh

(Valid at the time of going to press)

The handset is supplied with recommended batter-

ies.

Base station power consumption

General specifications

Questions and answers

If you have any queries about the use of your tele-

phone, visit our website at

www.gigaset.com/service

for 24-hour support. The table below contains a list of

common problems and possible solutions.

Authorisation

This device is intended for connection to analogue

networks outside the EEA (with the exception of Swit-

zerland) depending on national type approval.

Country-specific requirements have been taken into

considera

tion.

We, Gigaset Communications GmbH, declare that this

devic

e meets the essential requirements and other

relevant regulations laid down in Directive

1999/5/CE.

A copy of the 1999/5/EC Declaration of C

onformity is

available at this Internet address:

www.gigaset.com/docs

In standby mode

– Handset in base station

– Handset outside base station

approx. 1.3 W

During a call approx. 1.5 W

DECT standard is supported

GAP standard is supported

Range up to 300 m outdoors

up to 50 m indoors

Base station power supply 230 V ~/50 Hz

Environmental conditions

in operation

+5 °C to +45 °C, 20% to

75% elative humidity

Problem Cause Solution

Nothing

appears in

the display.

The handset is not

switched on.

The batteries are

flat.

Press the end call

a for approx.

5 seconds or place the

handset in the base

station.

Charge or replace the

bat

teries.

No wireless

nnection

to the base sta-

tion,

Base flashes in

e display.

The handset is out-

side the range of

the base station.

The handset is not

gistered.

The base station is

not

turned on.

Move the handset

oser to the base

station.

¢ page 11.

Check the mains con-

nector on the base sta-

tion ¢ page 4.

You cannot

hear a ringer/

dialling tone

from the fixed

line network.

The phone cord

sup

plied has not

been used or has

been replaced by a

new cord with the

wrong jack con-

nections.

Please always use the

phon

e cord supplied or

ensure that the

pin connections are

orrect when purchas-

ing from a retailer:

3-4 assignment of

tele

phone leads/

EURO CTR37.

Error tone

sou

nds after

system PIN

rompt.

PIN forgotten.

The system PIN you

ve entered is

incorrect.

Reset the system PIN to

the default 0000

¢ page 12.

All handsets are

de-registered. All set-

tings are reset. All lists

e deleted.

Problem Cause Solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens AL280 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens AL280

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info