Bedienungsanleitung Siemens AS150 (Seite 9 von 11) (Englisch)

61045

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Gigaset AS150 / English / A31008-M1811-R601-3-TN19 / Wytana.fm / 05.05.2008

Care

Wipe the base station, charging cradle and handset

with a damp cloth (do not use solvent) or an anti-

static cloth.

Never use a dry cloth. This can cause static.

Contact with liquid

If the handset has come into contact with liquid:

1 Switch off the handset and remove the bat-

tery pack immediately.

2 Allow the liquid to drain from the handset.

3 Pat all parts dry, then place the handset with

the battery compartment open and the keypad

facing down in a dry, warm place for at least

72 hours (not in a microwave, oven etc.).

4 Do not switch on the handset again until it is

completely dry.

When it has fully dried out, you will normally be

able to use it again.

Questions and answers

If you have any queries about the use of your tele-

phone, go to

www.siemens.com/gigasetcustomercare

for assistance 24/7. The table below contains a list

of common problems and possible solutions.

Authorisation

This device is intended for analogue phone

lines in your network.

Country-specific requirements have been

taken into consideration.

We, Siemens Home and Office

Communication Devices GmbH & Co. KG,

declare that this device meets the essential

requirements and other relevant regulations

laid down in Directive 1999/5/EC.

A copy of the 1999/5/EC Declaration of

Conformity is available at this Internet

address:

http://www.siemens.com/gigasetdocs

Problem Cause Solution

Nothing

appears in the

display.

The handset is not

switched on.

Battery pack is

flat.

Press the end call

key

a for approx.

5seconds or place

the handset in the

base.

Charge/replace the

battery pack (page 2).

No response

to key press,

"HOLD KEY"

appears in the

display.

The keypad lock is

activated.

Press the hash key

for approx. 2 sec

(page 3).

No wireless

connection to

the base, dif-

ferent icons

flash in the

display.

The handset is

outside the range

of the base.

The handset is not

registered.

The base is not

switched on.

Cords not routed

correctly

Move the handset

closer to the base.

(page 4).

Check the power con-

nector at the base

(page 2).

Check cord routing

(page 2).

You cannot

hear a ring/

dialling tone

from the fixed

network.

The supplied

phone cord was

not used or it has

been replaced by

a new cord with

the wrong pin

assignment.

Please always use the

supplied phone cord

and ensure that the

pin connections are

correct when purchas-

ing a new one

(page 2).

Error tone

after entering

system PIN.

Forgot PIN

The system PIN

entered is incor-

rect.

Restore the system

PIN to the factory set-

ting (0000). To do this

disconnect the mains

unit

¢hold down the

paging-key ¢recon-

nect the mains unit

hold the paging key

down for at least a

further 2 seconds

then release it.

The resetting proce-

dure is carried out.

The handsets are

deregistered. The

calls list is deleted.

Problem Cause Solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens AS150 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens AS150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info