Bedienungsanleitung Siemens AS185 (Seite 1 von 2) (Englisch)

101231

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Gigaset AS185_UK _ A31008-M2036-L151-1-7619 _ 11. Mai 2010

Quick start guide

AS185

GIGASET. INSPIRING CONVERSATION.

GIGASET HELPLINE: 0845 3670812

Pack contents

If you have purchased a model

with multiple handsets the

package should contain two

batteries, a battery cover, a

charging cradle

8 with mains

adapter

9 for each additional

handset.

one Gigaset AS185 Base station

2 one mains adapter

3 one Gigaset AS18H handset

4 one phone cord

5 two batteries

6 one battery cover

7 this Quick start guide

AS185

GIGASET. INSPIRING CONVERSATION.

Connecting the base station

¤ Connect power adapter 1 and

Phone jack

2 to the base and

place the cable recesses.

Please ensure the power lead is

fully inserted.

Please note:

u The mains adapter must always be connected, as the Phone will not operate

without a mains connection.

u Always use the power adapter and Phone cord supplied. Pin connections on

Telephone cables can vary.

Connecting the charging cradle (if included)

¤ Plug the mains adapter into the

plug socket

¤ Connect the flat plug from the

mains adapter

If you need to disconnect the plug from the

charging cradle, press the release button

3 and

disconnect the plug

Preparing the handset

Initial charging and discharging of the batteries

¤ Insert the batteries the right way

round. The polarity is indicated

in/on the battery compartment.

¤ Then slide the battery cover back

into the main casing until it clicks

into place.

f you need to open the battery cover, for

nstance to replace the batteries, place

your fingertip in the grooved area on the

op of the cover and slide down.

The correct charge status can only be displayed if

the batteries are first fully charged and discharged.

¤ Place the handset in the charger

for 7 hours.

Then remove the handset from the charger, make and receive Phone calls, setup the

Phone etc. and do not put it on the charger until the batteries are fully discharged.

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming

calls, and so that the alarm can be used.

Date: DD: MM: YY

“TOK

INT MENU

¤ Press the key below MENU on the

display screen to open the main

menu.

Date/Time

“ OK

¤ Press the bottom of the control

key ...

... until the

Settings menu item

appears.

¤ Press the key below OK on the

display screen to confirm your

selection.

The

Date/Time menu item appears on

the display.

¤ Press the key below OK on the

display screen to open the input

field.

Settings

“ OK

¤ The active cursor position is flashing.

Enter day, month and year as an

6-digit number via the handset,

e.g.

Q 1 1Q1Q for 01/10/10.

Answer machine

Message Indication Key ‘ on handset will flash to indicate one or all of the

following events:

u missed calls (if caller ID is enabled for your line numbers will be shown)

u new messages on the answer machine

u new Text messages (SMS) received

Activating/deactivating the answer machine

MENU ¢ Voice Mail ¢ OK ¢ Answer Mach. ¢ OK (

‰

=on)

If the answer machine is activated, the answering machine icon ± will be displayed

in the header.

To retrieve your messages, just press the flashing

‘ key on your handset.

Dial tone

The dial tone will only be heard when pressing the c call button for 2 seconds.

A short press will open the redial list.

You can also use the

speaker button.

Display in idle status

u 2: internal number, if more then one handset is registered

: answering machine is activated

u Battery charge status:

–

= e V U (empty to full)

–

= flashes: batteries almost empty

–

e V U flashes: charging procedure

Registration handset

Your handsets should already be registered by default, if your handset is flashing the

text "No Base" then it can be that:

u Your base station is not switched on, please check if the power supply is connected

properly.

u There is too much distance between the handset and base.

u Your handset has not been pre-registered in the factory.

In the case that the handset has not been pre-registered, or you want to register an

additional handset to your base station, use the manual registration procedure

below.

Automatic registering procedure

Manual registration procedure

1. On the handset:

MENU ¢ Settings ¢ OK ¢ Handset ¢ OK ¢ Register HS ¢ OK ¢ enter the

system PIN for the base and press

OK. Default PIN = 0000

2. On the base station:

Within 60 seconds of entering the system PIN, press and hold the registration/paging

key (min. 3 seconds). Registration takes approx. 1 minute.

You can register up to four handsets to your base. You can also register other Gigaset

handsets and handsets from other devices with GAP functionality.

Put into base

Place the handset with the

display facing up in the base

station.

The handset registers

automatically. Registration

can take up to 5 minutes.

Do not remove the handset

from the base station during

this time.

Put into base

Registering

Frequently asked questions

Q: There is no dial tone.

A: Press call button for 2 seconds (long press) to obtain dial tone.

A short press opens the redial list.

Q: The line is crackling / not clear.

A: Have you used the new line cable provided? Please do not use an old cable.

Q: The display is not clear / seems to be broken.

A: The display is protected by a plastic film, please make sure you have removed

the protective film.

Q: The handset is not registered.

A: If your handset is not registered, please follow the Registration handset procedure.

(Described on this page)

Q: The caller ID is not working.

A: Have you subscribed to this service (CLIP) from your provider?

Q: Message indicator flashing and I cannot retrieve my message.

A: Message indicator will flash to indicate missed calls as well as new messages of text

messages. (Described on this page)

Please check:

Have you used the phone cord supplied 

Have you fully inserted the power cable into the base station 

Have you inserted the batteries correctly 

Have you charged the batteries for 7 hours 

Have you set up the Date/Time 

To download the latest software and manuals, visit our web-site: http://www.gigaset.com

You have questions? As a Gigaset customer, you can take advantage of our comprehensive

service offerings. You can find help quickly in this User Manual and in the service pages of

our Gigaset online portal: http://www.gigaset.com

Product may not be fully compatible with the national telephone network. It is clearly

specified on the box near the CE mark as well as on the bottom of the base station for which

country/countries the equipment has been developed. If the equipment is used in a

manner inconsistent with this advice or with the instructions of the manual and on the

product itself, this may have implications on the conditions for warranty or guarantee

claims (repair or exchange of product).

In order to make use of the warranty, the product purchaser is asked to submit a receipt

which proves the date of purchase (date from which the warranty period starts) and the

type of goods that have been purchased.

If you have problems setting up or operation this product please call

GIGASET UK HELPLINE 0845 3670812

GIGASET IRL HELPLINE 1850 777277

Siemens AS185 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens AS185

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info