Bedienungsanleitung Siemens ax72 (Seite 4 von 16) (Englisch)

296325

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

left page (4) of AX72 Pegasus-DTC, SUG, en, A31008-H2860-A1-2-7619 (04.10.2005, 10:58)

VAR Language: en; VAR issue date: 050307

When charging is in progress h is

displayed.

Charging time

An empty battery is fully charged after

about 2 hours. Charging is only possible

within a temperature range of

+5 °C to +40 °C. If the temperature ris-

es/falls 5 °C above/below this, the charge

symbol flashes a warning. The mains volt-

age specified on the power supply unit

must not be exceeded (Operating time,

p. 12).

Only use the power supply unit provided!

Display while in service

Charge level display during operation

(empty - full):

adg.

A beep sounds when the battery is nearly

empty. The charge level of the battery is

only displayed correctly after an uninter-

rupted charging/discharging cycle. You

should therefore not remove the battery

unnecessarily and where possible not

terminate the charging process early.

Security

§Menu§ ¢ m ¢ Security

¢ Select function.

The phone and SIM card are protected

against misuse by several security codes.

Keep these confidential numbers in a safe

place where you can access them again if

required.

Codes

PIN control

You can stop the PIN prompt being

activated when the phone is switched on,

but you then risk unauthorised use of the

phone.

Press

§Change§

. Enter PIN and confirm

with

§OK§.

Change PIN

You can change the PIN to any 4- to 8-digit

number you find easier to remember.

Change PIN2

(Display only if PIN2 is available). Proceed

as with Change PIN.

Change phonecode

You define the phone code (4-8 digits)

when you call up a protected function for

the first time. It is then valid for all phone-

code protected functions.

Clear SIM card barring

If the PIN is entered incorrectly three

times, the SIM card is barred. Enter the

PUK (MASTER PIN), provided by your serv-

ice provider with the SIM card, according

to instructions. If the PUK (MASTER PIN)

has been lost, please contact your service

provider.

Preventing accidental activation

Even if PIN control is deactivated confirma-

tion is required to switch on the phone.

This prevents the phone from being

switched on accidentally, e. g. when car-

ried in a pocket or whilst you are on an

aircraft.

Press and hold the On/Off/End key

and confirm with §OK§. The phone switch-

es on.

Calling

Dialling with number keys

The phone must be switched on (standby

mode). Dial number (always with area

code, if necessary with international dial-

ling code). To dial international dialling

code press and hold

0 until a "+" is dis-

played. Press

§Country§ and select country.

Short press

§Clear§ to clear the last digit, a

long press clears the entire phone

number. To dial press the Call key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens ax72 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info