Bedienungsanleitung Siemens Climatix 2 (Seite 31 von 77) (Englisch)

693647

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

INSTRUCTION MANUAL OF THE SIEMENS CLIMATIX 2 CONTROL EQUIPMENT

The parameter setting is ranging from 0 – 190°C; the default value is 35°C.

The instructions for changing this parameter can be found in chapter 4.

The Differential B2 B8 reduce parameter determines the maximal difference (in Kelvin) between

the boiler temperature B2 during reduce and the flue gas temperature B8. The setting 25 K means

that the difference between the flue gas temperature during reduce and the boiler temperature can

be 25 K at the maximum, otherwise the error mode “Loss of flame – reduce“ is activated.

The parameter setting is ranging from -30 to 60 K; the default value is 25 K.

The instructions for changing this parameter can be found in chapter 4.

The Error delay number cycles parameter determines how many cycles of feeding during reduce

must pass before the error mode “Loss of flame – reduce” is activated. It is determined according

to the difference between the boiler temperature B2 and the flue gas temperature B8 (see the

Differential B2 B8 reduce parameter).

The parameter setting is ranging from 0 – 20 cycles; the default value is 3 cycles.

The instructions for changing this parameter can be found in chapter 4.

The Delay time of ignition after reduce parameter determines how long the temperature

conditions for ignition are ignored after the switchover from reduce to operation and determines the

time which is necessary for the boiler to begin to burn. If this time passes and the conditions for the

boiler operation are not met, the automatic ignition is activated.

This parameter can be found only in the configuration Ignition – YES.

The parameter setting is ranging from 0 - 600 s; the default value is 280 s.

The instructions for changing this parameter can be found in chapter 4.

The Differential B8 B2 operation parameter determines the minimal difference (in Kelvin)

between the flue gas temperature B8 and the boiler temperature B2 in operation. The setting 1

K means that the flue gas temperature B8 in operation must be by 1 K higher than the boiler

temperature, otherwise the error mode “Loss of flame - operation” is activated.

This parameter can be found only in the configuration Ignition – NO.

The parameter setting is ranging from -10 to 30 K; the default value is 1 K.

The instructions for changing this parameter can be found in chapter 4.

The Hysteresis differential B8 B2 operation parameter determines when the acceptable

operation state of the boiler is re-evaluated.

In order to deactivate the error mode “Loss of flame – operation“, the flue gas temperature must be

higher than Differential B8 B2 operation + Hysteresis differential B8 B2 operation.

This parameter can be found only in the configuration Ignition – NO.

The parameter setting is ranging from 1 - 30 K; the default value is 1 K.

The instructions for changing this parameter can be found in chapter 4.

The Delay of loss of flame parameter determines how long the flue gas temperature B8 can be

beyond permitted limits compared to the boiler temperature B2, without activation of the error

mode “Loss of flame – operation“.

This parameter can be found only in the configuration Ignition – NO.

The parameter setting is ranging from 0 – 800 s; the default value is 400 s.

The instructions for changing this parameter can be found in chapter 4.

If for any reasons (e.g. a lack of fuel in the storage tank) the boiler temperature falls below the limit

Low boiler temperature for the duration of Delay, the boiler is put out of operation and reports a

failure. During the first 30 min. of ignition this condition does not apply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens Climatix 2 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info