Bedienungsanleitung Siemens Climatix 2 (Seite 47 von 77) (Englisch)

693647

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

INSTRUCTION MANUAL OF THE SIEMENS CLIMATIX 2 CONTROL EQUIPMENT

indicator on button “A”.

If all appliances are heated up, the boiler switches to ‘reduce’ - see chap. 6.2. It is indicated with

the mode “External OFF” on the display and with the blinking green light of the indicator on button

“A”.

If a demand for heating from any appliance is received, the furnace is blown by the fan and the

normal operation of the boiler continues. It is indicated with the mode “Operation” on the display

and with the green light of the indicator on button “A”.

When the boiler switches to the mode ‘normal operation’, the furnace begins to burn again. If the

furnace burns insufficiently even if the time set in Delay time of ignition after reduce (see chap.

6.2.1.) has already passed, the automatic ignition is put into operation.

7.1.6. FLUE DAMPER CONFIGURATION

The selection Flue damper (YES/NO) defines whether the boiler is equipped with the flue damper,

which is automatically controlled according to the flue gas temperature in the chimney, or not.

This additional attachment is currently being developed and it is not a part of the existing boilers.

The default value is NO. The instructions for changing this parameter can be found in chapter 4.

7.1.7. INFLUENCE OF APPLIANCE ON RETURN TEMPERATURE CONFIGURATION

The selection Influence of appliance on return temperature (YES/NO) is a special way to

protect the return valve of the boiler against the low-temperature corrosion.

The selection Influence of appliance on return temperature – YES is used if the boiler is

installed into the heating system according to the instructions described in chap. 11.3. It means

that the primary circuit of the boiler does not include the mixing valve Y7 that would control the

return valve temperature but the temperature is controlled by switching the individual appliances

(heating circuits, DHW storage tank).

This setting cannot be used if the boiler has a buffer storage tank or if more boilers are connected

in a cascade!

The selection Influence of appliance on return temperature – NO is used if the boiler is

protected against low-temperature corrosion by the mixing valve Y7 in the primary circuit of the

boiler– see instructions in chap. 11.1., 11.2., or 11.4.

The default value is NO. The instructions for changing this parameter can be found in chapter 4.

7.1.8. BUFFER CONFIGURATION

The selection Buffer (YES/NO) defines whether the heating system is equipped with a buffer

storage tank or not.

The setting Cascade – boiler 2, boiler 3, boiler 4 is incompatible with the configuration setting

Buffer (see chap. 7.1.).

The default value is NO. The instructions for changing this parameter can be found in chapter 4.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens Climatix 2 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info