Bedienungsanleitung Siemens DE1518527M (Seite 8 von 24) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Türkisch)

652225

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

A fault, what to do?

Attention!

Repairs must only be carried out by an authorised technician. Improper repairs can lead to risk of serious injury to

the user.

If your appliance does not operate as required, it is often due to a very minor problem. Please check whether you can remedy

the fault yourself by using the following guidelines. You will save yourself the costs of an unnecessary visit by customer service

personnel.

Faults that the customer can troubleshoot himself

Fault Cause Solution

Water ﬂow-rate is too low The ﬁlter in either the water tap or the

showerhead is clogged.

Remove the ﬁlter and either clean it or

descale it.

A high water temperature is

set, but it is not reached.

The continuous-ﬂow heater is connected

to a thermostatically-controlled water tap.

Set the temperature on the continuous-ﬂow

heater to „60 °C“.

The display is blank. The fuse in the fusebox has tripped/blown. Check the fuse in the fusebox.

The water is not warm. The supply temperature has reduced. Reduce the water ﬂow on the taps until the

desired water temperature is reached.

The temperature of the water

leaving the tap is higher than

the set temperature.

The temperature of the water supplying the

continuous-ﬂow heater is higher than the

set temperature (e. g. due to pre-warmed

water supplied from a solar water heater).

The thermostatic premixer in the domes-

tic supply must be set accordingly to lower

temperatures.

“°C” ﬂashes in the display. The power limit has been reached. Reduce the water ﬂow at the tap or lower the

temperature setting on the appliance.

If the fault could not be eliminated, please call customer service.

Faults that the customer service specialist should troubleshoot

Fault Cause Solution

Water ﬂow-rate is too low

despite cleaning of ﬁlter using

the water tap or showerhead

A ﬁlter in the appliance is clogged. Get a servicing expert to clean the appliance.

The display is blank despite

fault-free function of the

mains electricity supply fuses.

There is a fault in the appliance. Get a servicing expert to check the appliance.

The display shows the error

code “E..”.

There is a fault in the appliance. Get a servicing expert to check the appliance.

Faults that are automatically remedied

Fault Cause Solution

The display shows “00,0°C”. The air sensor in the appliance detects air

in the water and momentarily switches the

heating element off.

After a few seconds, the continuous-ﬂow

heater automatically goes back into operation.

Guarantee

The guarantee conditions for this appliance are as deﬁned by

our representative in the country in which it is sold.

Details regarding these conditions can be obtained from the

dealer from whom the appliance was purchased. The bill of

sale or receipt must be produced when making any claim

under the terms of this guarantee.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DE1518527M Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info