Bedienungsanleitung Siemens DE24307M (Seite 7 von 28) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Türkisch)

652235

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Operating the appliance

Switching the appliance on and off

The continuous-ﬂow heater switches on and heats the water

when the warm water tap is opened. It switches off again if

the water tap is closed.

The factory default setting for the warm water outﬂow tem-

perature is 55 °C.

Note: The electronic control unit senses the input water’s

temperature and rate of ﬂow and automatically adjusts the

power consumption in order to obtain the set output water

temperature (up to the power limit).

Increasing the water temperature

If the supply water temperature is low and the ﬂow-rate is

high, then it may happen that the set output water tempera-

ture is not obtained because the power limit is exceeded.

This is signalled by rapid ﬂashing of the status display.

■ If this happens, then slightly close the warm water tap.

Status display

LED Appliance status

Off Off

Lights green On

Flashes green (1/s) The set temperature is not obtained;

the rate of water ﬂow is too high for

appliance rating (the appliance has

reached the power limit). See “A fault,

what to do?”

Flashes green (2/s) Cold-water rinse-through phase

Flashes red See “A fault, what to do?”

Startup after power failure

■ Open the warm water tap fully and allow water to ﬂow

until it is warm.

Using the appliance after switching off

the water supply

■ Switch off the appliance (unscrew the fuse in the

fusebox).

■ Open the warm water tap and keep it open until the air

has been completely forced out of the water pipe.

■ Switch the fuse back on again.

■ Open the warm water tap fully and allow water to ﬂow for

at least one minute,

Only then (for safety reasons) will the appliance begin to

heat. The appliance is now ready to operate.

Winter operation

Note: It is possible in winter that the supply temperature of

the water is reduced and the required outlet temperature is

no longer achieved.

■ Reduce the water ﬂow at the tap until the desired water

temperature is reached.

Cleaning

■ Only wipe off the appliance using a moist cloth.

■ Do not use acidic or abrasive cleaning materials.

■ Do not use a steam cleaner.

Customer Service

We ask you to always provide the E-No. and the FD-No. of

your appliance when calling in a customer service engineer.

You will ﬁnd the numbers on the ratings plate on the inner

side of the front ﬂap.

The contact information for your country can be found on

the last pages of these instructions.

Environmentally-friendly disposal

■ Dispose of the packaging in an environmentally sound

manner.

This appliance is labelled in accordance with Euro-

pean Directive 2012/19/EU concerning used elec-

trical and electronic appliances (waste electrical

and electronic equipment – WEEE).

The guideline determines the framework for the

return and recycling of used appliances as appli-

cable throughout the EU.

Please ask your specialist retailer about current

disposal facilities.

Subject to change without notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DE24307M Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info