Bedienungsanleitung Siemens DG15602 (Seite 16 von 20) (Deutsch, Englisch)

652204

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

VI.

Electrical connection 230 V AC

To guarantee compliance to relevant safety regulations, an

all-pole separator must be ﬁtted during installation. The con-

tact opening must be at least 3 mm.

If the appliance is connected to the power supply by a plug,

the disconnecting device is not required if the plug is acces-

sible to the user.

Appliances ﬁtted with plugs may only be connected to cor-

rectly earthed electrical sockets. Do not use multiway adap-

tors or pushon terminal strips.

Do not connect the appliance to the power supply until it is

mounted on the wall and ﬁlled with water.

Attention!

Only appliance installation with ﬁxed connection is

permissible in wet areas.

■ Remove screws 1 and 2.

■ Pull off temperature selector switch.

■ Remove screw 3.

■ Lift off the housing cover.

■ Connect electrical cable 4 to terminal 5.

■ Replace the housing cover and screw it on.

VII.

Limiting the water temperature

■ Fig. 1: Insert the screwdriver into gap a and remove

cover b.

■ Fig. 2: Insert pin c into one of the 4 holes in order to limit

the temperature:

Hole C: ≈ 35 °C

Hole B: ≈ 45 °C

Hole A: ≈ 55 °C

Hole O: ≈ 75 °C

■ Fig. 3: Replace cover b.

Startup

Attention!

Fill the appliance with water before inserting the

mains plug or turning on the mains voltage!

Otherwise the temperature protection will trip and

has to be reset by a trained service professional.

VIII.

Flow rate setting DO15652

■ Rinse out the appliance by fully opening the hot water

tap.

■ Set the ﬂow rate as per DIN 44531 or according to the

speciﬁcations of the ﬁttings manufacturer:

max. ﬂow rate: 10 l/min, i. e. the water ﬂows out at a rate

of 1 litre in 6 seconds.

■ Set the ﬂow rate by turning the screw valve on the upper

side of the mixer tap.

First heat-up

■ Turn the temperature selector switch to position “O”.

■ Switch on the fuses or insert the plug into the mains

socket.

■ Turn the temperature selector switch to position „III“.

■ Monitor the heating-up process (see „Technical Data“ for

heating times).

■ Check the temperature.

■ Turn the temperature selector switch to position „e“.

■ Hand over the installation and operating instructions to

the user and explain how the appliance operates.

■ Instruct the user regarding the necessity of regular

descaling.

Technical Data

DG15602

DO15652

Capacity

[l] 15.0

Rated output

[kW] 2

Rated voltage

[V] 230

Rated pressure

pressure-resistant operation [MPa (bar)] 0.6 (6)

unpressurised operation [MPa (bar)] 0 (0)

Weight

empty [kg] 11

ﬁlled [kg] 26

Heat-up time

from 12 °C to 60 °C [min] 25

from 12 °C to 75 °C [min] 75

Energy efﬁciency class

Hot water heating energy

efﬁciency

[%] 36.1

Load proﬁle

XXS

Annual energy consumption

[kWh] 510

Daily energy consumption

[kWh] 2.391

Sound power level

[dB] 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DG15602 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info