Bedienungsanleitung Siemens DH12103M (Seite 11 von 44) (Deutsch, Englisch, Holländisch, Französisch)

652229

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Operating instructions

Please read and observe the detailed safety instructions

at the start of these instructions!

■ Important: The appliance may never be exposed to frost!

Risk of electric shock!

Switch off the mains voltage supply immediately if

a fault occurs.

■ Immediately shut off the cold water supply to the appli-

ance should it leak.

Getting to know your appliance

The continuous-ﬂow heater heats the water as it ﬂows

through the appliance. The appliance only consumes power

during this period.

This appliance can supply hot water to taps in several dif-

ferent locations. It should be installed close to the tap that

is used the most frequently. This will enable you to reduce

energy consumption.

Operating the appliance

■ Turn on the hot-water tap.

The continuous-ﬂow heater switches on automatically and

heats the water as it ﬂows through the appliance.

The heater switches off again when you turn off the tap.

Increasing the water temperature

When the tap is turned on fully, it is possible that the heater

capacity is not sufﬁcient to heat the water to the required

temperature.

■ Turn the tap off slightly. The water ﬂows through the

appliance more slowly and reaches a higher temperature

as a result.

Decreasing the water temperature

■ Mix with cold water.

Saving energy

To minimise energy consumption when turning off the hot

water:

– Turn off the hot-water tap slowly in order to use the

residual heat of the continuous-ﬂow heater.

– This also prevents the water temperature from brieﬂy

increasing above the preselected temperature if the hot-

water tap is turned on again within the next few minutes.

To obtain particularly uniform hot-water temperatures, it is

recommended to use thermostatically-controlled premixers.

The thermostatically-controlled premixer must be suitable

for hydraulically controlled continuous-ﬂow heater.

Winter operation

Note: It is possible in winter that the supply temperature of

the water is reduced and the required outlet temperature is

no longer achieved.

■ In order to compensate for this temperature reduction,

please reduce the water quantity on the tap until the re-

quired water temperature is achieved.

Cleaning

■ Simply wipe the appliance with a damp cloth.

Do not use acidic or abrasive cleaning materials.

Notes: It is normally not necessary to descale the appliance.

However, extremely hard water and the frequent ﬂows of

very hot water can cause the appliance to scale up. In this

case please contact our after-sales service.

VII.

Dimensions

Special accessories

■ BZ45U20 Pipe set: for use of the continuous-ﬂow heater

as an under sink appliance

■ Intermediate terminal block BZ45Z20M: Required when

the mains connecting cable is fed in through the bottom

access hole 14a.

■ Priority switch (load shedding relay) BZ45L21:

for operation with the priority circuit

■ Mounting set BZ45K24M: for surface-mount installation

■ Truncated connecting piece sealed at rear for water con-

nection from below (e. g. cold water connection via ﬁtting

mounted below heater):

Elbow joint, “cold” (right) Order no. 056169

Elbow joint, “hot”, (left) Order no. 255568

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DH12103M Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info