Bedienungsanleitung Siemens DH21100M (Seite 10 von 36) (Deutsch, Englisch, Polnisch, Türkisch)

652227

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Congratulations on purchasing this Siemens appliance. You

have acquired a top-quality product, which will give you a lot

of enjoyment.

Please read this installation and operating instruction

manual carefully, then act accordingly! Store for future

reference.

Installation instructions

Install the continuous-ﬂow heater as described in the

illustrated section. Observe the instructions in the text.

The illustrations can be found in the centre of the instruction

manual.

Installation

List of items supplied

1 Continuous-ﬂow heater

2 Installation template

3 Connection piece for hot water

4 Washer, red Ø 15 mm

5 Connection piece for cold water

6 Washer, Ø 24 mm

7 Mounting bolt

8 Wall plug

9 Securing nut

10 Threaded bushing

11 Cable grommet

II.

Wall mounting

There are two ways in which the continuous-ﬂow heater can

be mounted on the wall:

– Using the mounting bolt. Unevenness in the wall up to a

depth of 25 mm can be compensated for.

– Making use of the holes that were drilled for the old heater:

Use the mounting template to establish whether the exist-

ing holes line up properly.

The following describes the installation procedure using the

mounting bolt.

Marking the point for mounting the heater and selecting

the opening for the connecting cable (Fig. A)

Important!

Make sure that the connecting cable is isolated

from the mains electricity supply!

■ Place hole 3 in the mounting template over the cold-water

inlet.

■ Select the most suitable hole through which the con-

necting cable is be fed. The connecting cable must pass

through one of the six holes marked 14... Terminal

BZ45Z20M can be used if the cable is fed into the water

heater through one of the bottom holes marked 14a.

■ Mark the point 12 at which the mounting bolt is to be

inserted.

Fitting the mounting bolt and attaching the pipe

connecting pieces (Fig. B)

Open up the heater (Fig. C)

Punching out the holes at the rear of the heater for the

mounting bolt and the connecting cable

Important: When mounting the appliance, only the holes

actually required should be punched out. Any other holes

that are not going to be used must be sealed watertight.

Inserting the connecting cable (Fig. D)

■ Push the grommet 11 over the end of the connecting

cable.

Note: Do not use the grommet for a cable with a cross-sec-

tion of 16 mm

. The appliance must then be installed ﬂush

with the wall.

Attention: Without a grommet, the

DH18100/21100/24100M is splashproof only (IP 24).

■ Place the heater over the connecting cable.

■ Press the grommet into the hole in the rear wall of the

heater through which the cable should be fed. Ensure that

the edges of the grommet are ﬂush with the hole all the

way round.

■ Fit the heater onto the threaded bushing 8 and secure it

in place with the nut 9.

Compensating for unevenness in the wall (Fig. E)

■ The mixer and the warm water pipe may

be hot. Please inform and instruct children

appropriately.

■ Do not use aggressive or abrasive cleaning

detergents!

■ Do not use a steam cleaner.

■ The appliance is only to be descaled by a

suitably qualiﬁed specialist.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DH21100M Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info