Bedienungsanleitung Siemens DH40024M (Seite 9 von 76) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

652244

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Congratulations on purchasing this Siemens appliance. You

have acquired a top-quality product, which will give you a lot

of enjoyment.

Please read this installation and operating instruction

manual carefully, then act accordingly! Store for future

reference.

Installation instructions

Install the continuous-ﬂow heater as described in the

illustrated section. Observe the instructions in the text.

The illustrations can be found in the centre of the instruction

manual.

Installation

Unpacking/removing the cover

■ Unpack the appliance and check for transport damage.

■ Dispose of the packaging and, where applicable, the old

appliance, in an environmentally conscious manner.

II.

Preparation for installation

Important: Only use the enclosed installation set.

■ Shut off water supply. The electrical connection (connec-

tion cable) must be disconnected from the power supply.

Unscrew the fuse or switch off the circuit breaker.

III.

Wall mounting

■ The continuous-ﬂow heater must be ﬁtted securely to

the wall. If required, secure the appliance using the lower

adjusting screws.

■ The distance from the wall is variable. This allows you to

compensate for any unevenness in the wall surface.

■ The sleeve must ﬁt tightly round the connection cable. If

the sleeve is damaged during installation, the holes must

be sealed water-tight.

IV.

Water connection

■ The continuous-ﬂow heater must be vented. Open the

warm water tap fully and ﬂush out the appliance thorough-

ly for 1 minute.

■ The ﬂow-rate limiter must be installed in the old water

regulating valve.

Electrical connection

■ The electrical supply terminal can be ﬁtted at the top or

bottom. The sheath of the connection cable must extend

for at least 40 mm into the appliance.

Installation note

■ The installation of non plug-in ready appliances must be

undertaken by the respective utility operator or by a quali-

ﬁed specialist company, who can also assist you when

you are requesting the approval of the utility company for

installation of the appliance.

VI.

Startup

The device is compliant to IEC 61000-3-12.

■ At low water pipe pressure, check whether the II setting

switches on even when water is drawn from several cold-

water taps simultaneously. If not, remove the ﬂow limiter

(refer to additional information A).

■ Instruct the user with regard to the operation of the con-

tinuous-ﬂow heater.

A B

Additional information

■ If the water pressure of the interior system is low, do not

operate the continuous-ﬂow heater at full power, but re-

move the ﬂow limiter (Fig. A, 3.).

■ Priority circuit for the combined operation of electric stor-

age heaters (Fig. B).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DH40024M Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info