Bedienungsanleitung Siemens E45 (Seite 9 von 29) (Englisch)

40017

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Safety precautions

Gigaset E45 / English / A31008-M1751-R601-1-TJ19 / start_guide_time.fm / 01.08.2005

Manual registration of the Gigaset E45

If the handset does not activate automati-

cally when the battery pack is fitted, you

must first charge the battery pack.

You must activate manual registration of

the handset at both the handset and the

base station.

After it has registered, the handset returns

to idle status. The handset's internal

number is shown in the display e.g. INT 1.

If not, repeat the procedure.

1. On the handset

v ¢ Ð ¢ Handset ¢ Register H/Set

s Select base station, e.g. Base

1, and press

§OK§.

~ Enter the system PIN of the

base station (the default is

0000) and press

§OK§. The

screen will display, e.g. Base 1.

2. On the base station

Within 60 secs. press and hold the regis-

tration/paging key on the base station

(page 1) (approx. 3 secs.).

Headset socket

You can connect the following types of

headset (with jack connector): HAMA

Plantronics M40, MX100 and MX150.

If you do not connect a headset, please

insert the cover supplied for the headset

socket to guarantee the unit is still splash

proof.

Charging the battery pack

¤ Plug the mains adapter of the charging

cradle into a mains power socket.

¤ Place the handset in the cradle with its

display facing forward.

To charge the battery pack, leave the

handset in the charging cradle. If the

handset is activated, the flashing battery

icon e in the top right of the display indi-

cates that the battery pack is being

charged. During handset operation, the

battery icon indicates the charge status of

the battery pack (page 1).

Initial charging and discharging of the

battery pack

The correct charge status can only be dis-

played if the battery pack is first fully

charged and discharged.

¤ To do this, leave the handset in the

charging cradle continuously for ten

hours. Your handset need not be

switched on for it to charge.

¤ Afterwards, remove the handset from

the charging cradle and do not put it

back again until the battery pack is fully

discharged.

Please remember:

u Always repeat the charging and dis-

charging procedure if you remove the

battery pack from the handset and

insert it again.

Notes:

– Automatic registration is not possible when

the base station on which you wish to reg-

ister the handset is being used to make a

call.

– Each key press interrupts the automatic

registration.

– If automatic registration does not work,

you will have to register the handset manu-

ally.

Notes:

– The handset should only be placed in a

base station or charging cradle that is

designed for it.

– When the handset is in the cradle, it

charges even if it is switched off.

– If the handset has switched itself off

because the battery pack is flat and it is

then placed in the cradle, it will switch itself

on automatically.

– After the first battery charge and discharge

you may replace your handset in the charg-

ing cradle after every call.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens E45 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens E45

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info