Bedienungsanleitung Siemens ED811FQ15E (Seite 12 von 36) (Englisch)

791009

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

en Operating the appliance

1Operating the appliance

Oper at i ng t he appl i anc e

This chapter explains how to set a hotplate. The table

shows heat settings and cooking times for various

meals.

Tip: Switch on the ventilation system when you start

cooking and only switch it off a few minutes after you

have finished cooking. This is the most effective way to

remove the cooking vapours.

Note: Never operate the appliance without the metal

grease filter and the overflow container.

Switching the hob on and off

The main switch is used to switch the hob on and off.

To switch on: Touch the # symbol. An audible signal

sounds. The indicator next to the main switch and the

hotplate indicators ‹ light up. The hob is ready to use.

To switch off: Touch the # symbol until the indicator

goes out. All hotplates are switched off. The residual

heat indicator remains lit until the hotplates have cooled

down sufficiently.

Notes

■The hob switches off automatically if all hotplates

have been switched off for more than 20 seconds.

■The selected settings are stored for four seconds

after the hob has been switched off. If you switch it

on again during this time, the hob will operate using

the previously stored settings.

Setting the hotplate

The desired power level is set in the programming

panel.

Power level 1 = minimum power.

Power level 9 = maximum power.

Each power level has an intermediate setting. This is

marked with a dot.

Notes

■To protect the fragile parts of your appliance from

overheating and electrical overloading, the hob may

temporarily reduce the power.

■In order to prevent the appliance from producing

excess noise, the hob may temporarily reduce the

power.

Selecting a hotplate and heat setting

The hob must be switched on.

1. Touch the » symbol for the required hotplate. ¬

lights up on the display.

2. Then select the required heat setting from the

settings range.

The heat setting is set.

Changing the power level

Select the hotplate and set the desired power level in

the programming zone.

Switch off the hotplate

Select the hotplate and set it to ‹ in the programming

panel. The hotplate turns off and the residual heat

indicator appears.

Notes

■If no pan has been placed on the hotplate, the

selected power level flashes. After a certain time has

elapsed, the hotplate switches off.

■If a pan has been placed on the hotplate before

switching on the hob, it will be detected within

20 seconds of pressing the main switch and the

hotplate will be selected automatically. Once

detected, select the power level within the next

20 seconds or the hotplate will switch off.

If more than one pan is placed on the hob, only one

will be detected when switching it on.

 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens ED811FQ15E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens ED811FQ15E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info