Bedienungsanleitung Siemens EH675FFC1E (Seite 24 von 28) (Englisch)

790974

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

en Trouble shooting

3Trouble shooting

Tr oubl e s hoot i ng

Usually, faults are small matters that are easy to

eliminate. Please read the information in the table

before calling the after-sales service.

Notes

■If “ appears on the display, press and hold the

button for the relevant cooking zone in order to read

the fault code.

■If the fault code is not listed in the table, disconnect

the hob from the mains power supply and wait

30 seconds before reconnecting it. If this code is

displayed again, contact the technical after-sales

service and specify which fault code has appeared.

■If a fault occurs, the appliance will not switch to

standby mode.

Cleaning

How do I clean the hob?

Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-

water detergent (concentrated) or scouring pads.

You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning"

Display Possible cause Solution

None The power supply has been disconnected. Use other electrical devices to check whether a short-circuit has

occurred in the power supply.

The device has not been connected in accord-

ance with the circuit diagram.

Ensure that the device has been connected in accordance with

the circuit diagram.

Electronics fault. If the fault cannot be eliminated, inform the technical after-sales

service.

The displays flash The control panel is damp or an object is cover-

ing it.

Dry the control panel or remove the object.

The Ù indicator flashes in the

hotplate displays

A fault has occurred in the electronics. To acknowledge the fault, cover the control panel with your hand.

”ƒ The electronics have overheated and have

switched off the corresponding hotplate.

Wait until the electronics have cooled down sufficiently. Then

touch any symbol on the hob.

”… The electronics have overheated and have

switched off all hotplates.

”† + heat setting and acous-

tic signal

There is a hot pan in the area of the control

panel. There is a risk that the electronics will

overheat.

Remove the pan. The fault display goes out shortly afterwards.

You can continue to cook.

”† and acoustic signal There is a hot pan in the area of the control

panel. To protect the electronics, the hotplate

has been switched off.

Remove the pan. Wait for a few seconds. Touch any control. If the

fault display goes out, you can continue to cook.

”‚/”‡ The hotplate has overheated and switched itself

off to protect the work surface.

Wait until the electronics have cooled down sufficiently and

switch the hotplate on again.

”‰ The hotplate was operating for an extended

period without interruption.

The automatic safety switch-off function has been activated. See

section

“Š‹‹‹

“Š‹‚‹

The supply voltage is faulty; outside of the nor-

mal operating range.

Contact your electricity provider.

—…‹‹ The hob is not connected properly Disconnect the hob from the power supply. Ensure that it has

been connected in accordance with the circuit diagram.

Do not place hot pans on the control panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens EH675FFC1E Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens EH675FFC1E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info