Bedienungsanleitung Siemens EP7A6SC20N (Seite 7 von 16) (Englisch)

641276

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Gas burners en

Accessories

Depending on the model, the hob may include the

following accessories. These can also be acquired from

the Technical Assistance Service.

--------

Code

The manufacturer accepts no liability if these

accessories are not used or are used incorrectly.

ÄGas burners

Gas burners

Switching on manually

1. Press the control knob for the selected burner and

turn it anticlockwise to the highest power setting.

2. Hold an igniter or a naked flame (such as a lighter or

a match) against the burner.

Automatic ignition

If your appliance has automatic ignition (ignition plugs):

1. Press the control knob for the selected burner and

turn it anticlockwise to the highest power setting.

Sparks are produced on all burners while you are

pressing and holding the control knob. The burner

ignites.

2. Release the control knob.

3. Turn the control knob to the required position.

If the burner does not ignite, switch it off and repeat the

steps described above. This time, hold the control knob

down for longer (up to 10 seconds).

:Warning – Risk of deflagration!

If the burner does not switch on after 15 seconds,

switch off the control knob and open the door or

window in the room. Wait at least a minute before

igniting the burner again.

Note: It is important to keep the appliance clean. If the

ignition plugs are dirty, this may cause ignition faults.

Clean the ignition plugs regularly with a small non-

metallic brush. Take care to prevent the ignition plugs

from suffering any heavy knocks.

Safety system

Your hob is equipped with a safety system

(thermocouple) that cuts off the gas when the burners

are accidentally switched off.

To ensure that this device is active:

1. Switch on the burner as usual.

2. Without releasing the control knob, press and hold it

down firmly for 4 seconds after lighting the flame.

Switching off a burner

Turn the corresponding control knob clockwise to the 0

setting.

A few seconds after the burner is switched off, a sound

(thud) will be produced. This is not a fault - this means

that the safety device is no longer operating.

Warnings

It is normal to hear a soft whistling noise while the

burner is operating.

When first used, it is normal for the burner to give off

odours. This does not pose any risk and does not

indicate a malfunction. They will disappear in time.

Additional wok pan support

Only for use on wok burners

with pans with a round base.

The additional wok pan support

should be used to prolong the

appliance's useful life.

Additional support for

espresso makers

Only when using cookware with

a base less than 12 cm in diam-

eter on the smallest burner.

Simmer Cap

Lid specially designed to cook at

minimum power. For its use, the

Simmer Cap needs to be placed

on the auxiliary burner cap.

HZ298108 Wok attachment: Cast iron (mini-wok

burner)

HZ298107 Additional wok pan support: cast iron

(4-5 kW)

HZ298110 Additional wok pan support: steel enamel

HZ298114 Additional coffee maker support

HZ211310 Simmer Cap

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens EP7A6SC20N Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens EP7A6SC20N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info