Bedienungsanleitung Siemens ER7A6RD70D (Seite 7 von 16) (Englisch)

790983

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

en Getting to know your appliance

It is essential to ensure that all the burner parts and pan

supports are correctly installed for the appliance to

work correctly. Do not swap the burner caps around.

Always remove the pan supports carefully. When

moving a pan support, the pan supports next to it may

also move.

Residual heat indicator

Every burner on the hob has a residual heat indicator

that indicates whether it is hot or warm.

If • appears in the display the burner is still hot. As the

burner cools down further, the display changes to œ.

The display remains lit until the burner has cooled

sufficiently. Do not touch the respective burner if this

indicator is lit.

Accessories

Depending on the model, the hob may include the

following accessories. These can also be acquired from

the Technical Assistance Service.

--------

Code

The manufacturer accepts no liability if these

accessories are not used or are used incorrectly.

Inner flame on low power.

Burner parts

1 Ignition plug

2 Thermocouple

3 Burner ring

4 Burner cup

5 Burner cap







































Additional wok grid

Only suitable for use on wok

burners. Use cookware with a

rounded base.

To extend the service life of the

appliance, we recommend using

the additional wok grid.

Additional espresso maker

grid

Only suitable for use on the

smallest burner. Use cookware

with a diameter of less than

12 cm.

Simmer plate

This accessory part is only suita-

ble for simmering. It can be

used with the economy burner

or the standard-output burner. If

your hob has several standard-

output burners, we recommend

placing the simmer plate on the

rear or front-right standard-out-

put burner.

Place the accessory component

with the projections facing

upwards on the holder; never

place it directly on the burner.

HZ298114 Additional espresso maker grid

HZ298105 Simmer Plate

Gas burners en

ÄGas burners

Gas bur ner s

Switching on manually

1. Press the control knob for the selected burner and

turn it anticlockwise to the highest power setting.

2. Hold an igniter or a naked flame (such as a lighter or

a match) against the burner.

Automatic ignition

If the hob has automatic ignition (ignition plugs):

1. Press the control knob for the selected burner and

turn it anticlockwise to the highest power level.

While the control knob is held down, all the burners

will generate sparks and the ³ symbol will appear

on the display. The flame ignites. Wait a few

seconds.

2. Release the control knob.

3. Turn the control knob to the required position.

If the burner does not ignite, switch it off and repeat the

steps described above. This time, hold the control knob

down for longer (up to 10 seconds).

:Warning – Risk of deflagration!

If the flame does not ignite after 10 seconds, switch off

the burner and open a window or the door to the room.

Wait at least one minute before switching the burner on

again.

Note: It is important to keep the appliance clean. If the

ignition plugs are dirty, this may cause ignition

problems. Clean the ignition plugs regularly with a

small, non-metallic brush. Take care to prevent the

ignition plugs from suffering any heavy knocks.

Safety system

Your hob is equipped with a safety system

(thermocouple) that cuts off the gas when the burners

are accidentally switched off.

To ensure that this device is active:

1. Switch on the burner as usual.

2. Without releasing the control knob, press and hold it

down firmly for 4 seconds after lighting the flame.

Switching off a burner

Turn the control knob clockwise to position 0. The ‹

symbol will appear in the display and the residual heat

indicator will appear after a few seconds.

A few seconds after the burner is switched off, a sound

(thud) will be produced. This is not a fault - this means

that the safety device is no longer operating.

Warnings

It is normal to hear a soft whistling noise while the

burner is operating.

When first used, it is normal for the burner to give off

odours. This does not pose any risk and does not

indicate a malfunction. They will disappear in time.

An orange-coloured flame is normal. This is caused by

the presence of dust in the atmosphere, spilt liquids, etc.

If the burner flames are accidentally blown out, switch

off the burner operating control knob and do not try to

relight it for at least 1 minute.

JSettings table and tips

Set t i ngs t a bl e and t i ps

Suitable pans

The cookware must not overhang the edge of the hob.

Precautions for use

The following advice is intended to help you save

energy and prevent pan damage:

Burner Minimum diame-

ter of the cook-

ware base

Maximum diame-

ter of the cookware

base

Wok burner 22 cm 30 cm

High-output burner 20 cm 26 cm

Standard-output burner 14 cm 22 cm

Economy burner 12 cm 16 cm

Use pans which are the

right size for each burner.

Do not use small pans on

large burners. The flame

must not touch the sides of

the pan.

Do not use damaged pans,

which do not sit evenly on

the hob. Pans may tip over.

Only use pans with a thick,

flat base.

Do not cook without using a

lid and make sure the lid is

properly fitted. This wastes

energy.

Always centre the pan over

the burner, not to one side.

Otherwise it could tip over.

Do not place large pans on

the burners near the control

knobs. These may be

damaged by the very high

temperatures.

Place the pans on the pan

supports, never directly on

the burner.

Make sure that the pan

supports and burner caps

are correctly positioned

before using the appliance.

Siemens ER7A6RD70D Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens ER7A6RD70D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info