Bedienungsanleitung Siemens ET675FN17E (Seite 6 von 16) (Englisch)

527446

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

The hotplates

Residual heat indicator

The hob has a two-stage residual heat indicator for each

hotplate.

• appears in the display the hob is still hot. It may be used,

for example, to keep a small meal warm or to melt cooking

chocolate. As the hotplate cools down further, the display

changes to

œ. The display remains lit until the hotplate has

cooled sufficiently.

Setting the hob

This section informs you how to set the hotplates. The table

shows heat settings and cooking times for various meals.

Switching the hob on and off

The main switch is used to switch the hob on and off.

To switch on: touch the

# symbol. A signal sounds. The

display light above the main switch and the

‹ indicators light

up. The hob is ready for use.

To switch off: Touch the

# symbol until the display light above

the main switch and the displays go out. All hotplates are

switched off. The residual heat indicator remains on until the

hotplates have cooled down sufficiently.

Notes

■ The hob switches off automatically if all hotplates have been

switched off for more than 20 seconds.

■ The settings remain stored for 4 seconds after the hob has

been switched off. If you switch it on again during this time,

the hob will operate using the previously stored settings.

Setting a hotplate

Set the desired heat setting on the control panel.

Heat setting 1 = lowest setting

Heat setting 9 = highest setting

Every heat setting has an intermediate setting. This is identified

by a dot.

Setting the heat setting

The hob must be switched on.

1. Touch the ¹ symbol to select the hotplate.

‹ lights up in the heat setting display, ¬ lights up under the

heat setting display.

2. Set the desired heat setting in the control panel.

Changing the heat setting

Select the hotplate and set the desired heat setting in the

control panel.

Switching off the hotplate

Use the

¹ symbol to select the hotplate. Set the control panel

to 0. After about 10 seconds, the residual heat indicator

appears.

Notes

■ The last selected hotplate remains activated. You can set the

hotplate without selecting it again.

■ Hotplate temperature is regulated by the heat switching on

and off. The heat may also switch on and off at the highest

setting.

Hotplate Connecting and disconnecting

Single-circuit hotplate

Dual-circuit hotplate

Select the hotplate and touch the

Ð or ð symbol

Tri-circuit hotplate

Select the hotplate, touch the

Ð symbol, and the 2nd filament circuit is connected

Touch the

Ð symbol again and the 3rd filament circuit is connected

Extended cooking zone

Select the hotplate and touch the

Ð symbol

Connecting the hotplate: The corresponding indicator lights up.

Switching on the hotplate: The size of hotplate which was last set is automatically selected.

 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens ET675FN17E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens ET675FN17E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info