Bedienungsanleitung Siemens EX801KYW1E (Seite 50 von 56) (Englisch)

790955

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

en Trouble shooting

Demo mode

If the ± symbol is shown on the display, demo mode

is active. The appliance does not heat up in demo

mode. Disconnect the appliance from the power

supply.Wait a few seconds before reconnecting the

appliance. Then deactivate demo mode in the basic

settings within 3 minutes of switching on the appliance.

The cooking zone has been operating continuously for an

extended period.

The automatic safety shut-off function has been activated. See the section entitled

The hob is unable to connect to your home network or the

extractor hood. “ˆ‹‚‹

Acknowledge the fault code by touching any of the buttons. You can cook as usual

without a connection.

If this code is displayed again, contact the technical after-sales service.

The cooking sensor has overheated and the cooking zone has

been switched off. “‰ƒ‹ƒ

Wait until the cooking sensor has cooled down sufficiently before activating the func-

tion again.

The cooking sensor has overheated and all the cooking zones

have been switched off. “‰ƒ‹„

If you are not using the cooking sensor, remove it from the cookware and keep it

away from the other cooking zones and sources of heat. Switch the cooking zones

back on.

The battery in the cooking sensor is almost drained. “‰ƒ‹… Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the battery"

The connection to the cooking sensor has been broken.

“‰ƒ‹†

Switch the function off and then on again.

The cooking sensor is faulty. “‰ƒ‹‡ Contact the technical after-sales service.

The cooking sensor indicator will not light up and the cooking

sensor is not responding.

Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the battery"

If this does not solve the problem, press and hold the symbol on the cooking sensor

for 8-10 seconds and then reconnect the cooking sensor to the hob. See the section

entitled

If the problem persists, contact the technical after-sales service.

The indicator on the sensor flashes twice. The battery in the

cooking sensor is almost drained. You may be interrupted the

next time you cook by the battery running out.

Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the battery"

The indicator on the sensor flashes three times. The connec-

tion to the cooking sensor has been broken.

Press and hold the symbol on the cooking sensor for 8-10 seconds and then recon-

nect the cooking sensor to the hob. See the section entitled ~ "Connecting the

wireless temperature sensor to the control panel"

The operating voltage is incorrect/outside of the normal oper-

ating range. “Š‹‹‹/“Š‹‚‹

Contact your electricity supplier.

The hob is not connected properly —…‹‹ Disconnect the hob from the mains power supply. Make sure that it has been con-

nected as shown in the circuit diagram.

Problem Solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens EX801KYW1E Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens EX801KYW1E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info