Bedienungsanleitung Siemens EX807LYV5E (Seite 11 von 48) (Englisch)

790762

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Operating the appliance en

1Operating the appliance

Oper at i ng the appl i anc e

This chapter explains how to set a hotplate. The table

shows heat settings and cooking times for various

meals.

Switching the hob on and off

Use the main switch to switch the hob on and off.

When you first switch on the appliance, you will be

prompted to set up your home network. The D symbol

will be lit dimly for a few seconds on the display panel.

To begin setting up the connection, touch the

D sensor and proceed in accordance with the

information given in the section entitled ~ "Home

Connect".To exit initial set-up, touch any sensor.

To switch the hob on and off, touch the # symbol. An

audible signal will sound. The symbols for the cooking

zones and the functions available at this time will light

up.The hob is ready to use.

To switch the hob off, touch and hold the # symbol

until all indicators go out. The residual heat indicator will

remain lit until the cooking zones have cooled down

sufficiently.

Notes

■If the appliance has not been connected to your

home network or the connection has been broken,

network connection initial set-up will be activated

whenever you switch on the hob.

■The hob will automatically switch itself off if the

cooking zones have been switched off for a few

seconds.

■The settings are stored for 4 seconds after the hob

has been switched off. If you switch the hob back on

during this time, the hob will operate using the

stored settings.

Setting a hotplate

Set the desired heat setting in the settings area.

Heat setting 1 = lowest setting.

Heat setting 9 = highest setting.

Every heat setting has an intermediate setting. This is

marked with †.

Note: The left-hand hotplates are set in the settings

area on the left and the right-hand hotplates are set in

the settings area on the right.

Notes

■To protect the fragile parts of your appliance from

overheating and electrical overloading, the hob may

temporarily reduce the power.

■In order to prevent the appliance from producing

excess noise, the hob may temporarily reduce the

power.

Selecting a hotplate and heat setting

The hob must be switched on.

1. Touch the " and Ä symbols for the required

hotplate.

The ‹ indicator gets brighter.

2. Swipe your finger over the relative settings area until

the required heat setting lights up.

The heat setting is set.

Changing the power level

Select the hotplate and set the desired power level in

the programming zone.

Switch off the hotplate

Select the hotplate and set it to ‹ in the programming

panel. The hotplate turns off and the residual heat

indicator appears.

Notes

■If no pan has been placed on the hotplate, the

selected power level flashes. After a certain time has

elapsed, the hotplate switches off.

■If a pan has been placed on the hotplate before

switching on the hob, it will be detected within

20 seconds of pressing the main switch and the

hotplate will be selected automatically. Once

detected, select the power level within the next

20 seconds or the hotplate will switch off.

 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens EX807LYV5E Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens EX807LYV5E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info